Search results
Jump to navigation
Jump to search
- equipment=True |Has make=Weller |Has model=WES51 |Is located in facility=Tool Room |Is located in facility=The Hub |Is used in domain=Electronics |Has function=Soldering16 KB (2,328 words) - 15:16, 15 June 2023
- Machine Shop (section Canvas Certification)Machine Shop has a specific organization to it. Put whatever you use back where it belongs. There is a place for everything and everything has a place. This8 KB (1,208 words) - 23:16, 25 August 2023
- Wood Shop (section Canvas Certification)Wood Shop has a specific organization to it. Put whatever you use back where it belongs. There is a place for everything and everything has a place. This10 KB (1,563 words) - 23:17, 25 August 2023
- Welding Shop (section Canvas Certification)Welding Lab has a specific organization to it. Put whatever you use back where it belongs. There is a place for everything and everything has a place. This10 KB (1,537 words) - 23:19, 25 August 2023
- The Hub (section Canvas Certification)approximately 8 open workbenches that are open for general use. Each of these has a permanent home that is marked on the floor. Each of these tables should18 KB (1,722 words) - 23:06, 25 August 2023
- Prototype Lab (section Canvas Certification)printer that the Prototype Lab has that is an SLA printer. It utilizes the Upside Down or Inverted orientation. The resin tank has a clear bottom with a surface18 KB (2,851 words) - 19:50, 7 September 2023
- PCB Lab (section Canvas Certification)The PCB Lab has a specific organization to it. Put whatever you use back where it belongs. There is a place for everything and everything has a place. This9 KB (1,308 words) - 23:18, 25 August 2023
- The Vault (section Canvas Certification)that would require an additional rule to be added to this list. The Vault has a specific organization to it. Put whatever you use back where it belongs7 KB (1,057 words) - 23:21, 25 August 2023
- Tool Room (section Canvas Certification)The Tool room is normally off limits to students. There is no Canvas certification for the Tool Room.2 KB (88 words) - 15:44, 22 May 2023
- Heat Press (section Certification)material on top of the graphic. This should be left on until after the transfer has occurred. Protective Sheets - The heat resistant sheets in the press that11 KB (1,610 words) - 23:41, 25 August 2023
- Belt/Disc Sander (section Certification)sanding power down the dust collector and sander. 10. Make sure all motion has stopped before cleaning the machine. 11. Reset the space. Complete the Wood5 KB (667 words) - 00:23, 26 August 2023
- Dissolvable Support Bath (section Certification)part completely submerged. Periodically check the part until all support has been dissolved. Always wear safety equipment when opening the bath. The bath8 KB (1,209 words) - 12:17, 23 January 2023
- Vertical Wood Bandsaw (section Certification)used to rip wood because it is much safer than a radial arm saw and also has a smaller saw cut, so it wastes less wood. This becomes very important when6 KB (829 words) - 00:31, 26 August 2023
- Rework Station (section Certification)reworking process. The Air Bath has a power switch on the left, three buttons on the right, and a screen on the right. The switch has 3 positions which allows10 KB (1,478 words) - 00:00, 26 August 2023
- Oscillating Spindle Sander (section Certification)machine contains a 1HP motor and has 10 different sanding spindles ranging from 1/4" to 4" in diameter. The cast iron table has an opening that provides clearance6 KB (904 words) - 00:28, 26 August 2023
- 3D Scanners (section Certification)with black and shiny surfaces. Artec Eva’s ease of use, speed and precision has made it an essential product for a wide range of industries. From rapid prototyping8 KB (1,212 words) - 23:23, 25 August 2023
- F370 3D Printer (section Certification)from the Prusa printers when they are full. Currently, the Prototype Lab has two F370 printers available for use. Printing parts on the F370 costs more16 KB (2,591 words) - 23:48, 25 August 2023
- Soldering Irons (section Certification)to perform the live solder demonstration required for your soldering certification. This nostalgic set of videos from PACE are quite old, but surprisingly13 KB (1,534 words) - 00:03, 26 August 2023
- Pick and Place (section Certification)completion, refer to the instructions on the Reflow Oven wiki. The solder has not been solidified yet, so be careful with your board so you do not move9 KB (1,190 words) - 23:59, 25 August 2023
- Rotary Punch (section Certification)desired punch and release the lever while rocking the carousel to verify it has locked in place. Lift the bottom locking lever for the lower carousel and5 KB (690 words) - 00:17, 26 August 2023