Search results

• The Hub (section 2. Reset the Space)
  approximately 8 open workbenches that are open for general use. Each of these has a permanent home that is marked on the floor. Each of these tables should
  18 KB (1,722 words) - 23:06, 25 August 2023
• Welding Shop (section 2. Reset the Space)
  Welding Lab has a specific organization to it. Put whatever you use back where it belongs. There is a place for everything and everything has a place. This
  10 KB (1,537 words) - 23:19, 25 August 2023
• Wood Shop (section 2. Reset the Space)
  Wood Shop has a specific organization to it. Put whatever you use back where it belongs. There is a place for everything and everything has a place. This
  10 KB (1,563 words) - 23:17, 25 August 2023
• The Vault (section 2. Reset the Space)
  that would require an additional rule to be added to this list. The Vault has a specific organization to it. Put whatever you use back where it belongs
  7 KB (1,057 words) - 23:21, 25 August 2023
• PCB Lab (section 2. Reset the Space)
  The PCB Lab has a specific organization to it. Put whatever you use back where it belongs. There is a place for everything and everything has a place. This
  9 KB (1,308 words) - 23:18, 25 August 2023
• Prototype Lab (section 2. Reset the Space)
  to cure liquid resin into a hard plastic. The Form 2 is the only 3D printer that the Prototype Lab has that is an SLA printer. It utilizes the Upside Down
  18 KB (2,851 words) - 19:50, 7 September 2023
• Heat Press
  material. After the time at temperature has been set, the material should be placed between the platens and pressed for 2-3 seconds to remove any wrinkles. Now
  11 KB (1,610 words) - 23:41, 25 August 2023
• Rework Station
  reworking process. The Air Bath has a power switch on the left, three buttons on the right, and a screen on the right. The switch has 3 positions which allows
  10 KB (1,478 words) - 00:00, 26 August 2023
• Tool Room
  open during certain hours, so please view the Schedule below. The current Ace of the Tool Room is Mary Groom (mgroom19@georgefox.edu). View the most up-to-date
  2 KB (88 words) - 15:44, 22 May 2023
• Dissolvable Support Bath
  Immediately inform the Aces of the Lab and/or Justin. What to do in the event of a spill: Evacuate the lab and shut it down until the spill has been properly cleaned
  8 KB (1,209 words) - 12:17, 23 January 2023
• Machine Shop
  Machine Shop has a specific organization to it. Put whatever you use back where it belongs. There is a place for everything and everything has a place. This
  8 KB (1,208 words) - 23:16, 25 August 2023
• Formlabs 3D Printer (redirect from Formlabs Form 2)
  print is under the approved cost/size cutoff ($7), or the person printing has special approval to exceed this limit. If a window pops up saying the print
  14 KB (1,983 words) - 13:09, 2 June 2023
• Soldering Irons
  "tack" these same leads with solder - just to hold it. The rest of the video has great examples of IC's being soldered. Basic Soldering Lesson 8-9: We don't
  13 KB (1,534 words) - 00:03, 26 August 2023
• Markforged 3D Printer
  requires an account to use. Purge - Rapid printing of excess material which has been sitting in the machine lines for a long period of time. This helps ensure
  10 KB (1,239 words) - 23:53, 25 August 2023
• Metal Laser Cutter
  of material from the surface of the metal along an established line. This has great accuracy but only produces a thin line. Raster - Very similar to an
  12 KB (1,844 words) - 00:12, 26 August 2023
• Belt/Disc Sander
  sanding power down the dust collector and sander. 10. Make sure all motion has stopped before cleaning the machine. 11. Reset the space. Complete the Wood
  5 KB (667 words) - 00:23, 26 August 2023
• Hydraulic Press
  will also press the pin out after insertion. The pin has an outer diameter of .375" and the block has 4 holes that have been reamed to .374" The dowel pin
  12 KB (1,836 words) - 00:10, 26 August 2023
• CNC Router
  the material because I'm cutting beyond 3/4" deep? 8. Has the proper program been loaded? 9. Has the Z-zero position been set using the material bed and
  18 KB (3,021 words) - 00:23, 26 August 2023
• F370 3D Printer
  if it is highly detailed and/or has holes that require fairly high tolerances. If it is a small, detailed part, a Form 2 printer should suffice. If the
  16 KB (2,591 words) - 23:48, 25 August 2023
• Hand Router
  Make sure the bit has a bearing guide. 4. Verify the router is unplugged and place the router upside down on the bench. 5. Select the 1/2" or 1/4" collet
  9 KB (1,305 words) - 00:26, 26 August 2023

View (previous 20 | next 20) (20 | 50 | 100 | 250 | 500)