Search results
Jump to navigation
Jump to search
Did you mean: has ace
- The Hub (section 2. Reset the Space)approximately 8 open workbenches that are open for general use. Each of these has a permanent home that is marked on the floor. Each of these tables should18 KB (1,722 words) - 23:06, 25 August 2023
- Welding Shop (section 2. Reset the Space)Welding Lab has a specific organization to it. Put whatever you use back where it belongs. There is a place for everything and everything has a place. This10 KB (1,537 words) - 23:19, 25 August 2023
- Wood Shop (section 2. Reset the Space)Wood Shop has a specific organization to it. Put whatever you use back where it belongs. There is a place for everything and everything has a place. This10 KB (1,563 words) - 23:17, 25 August 2023
- The Vault (section 2. Reset the Space)that would require an additional rule to be added to this list. The Vault has a specific organization to it. Put whatever you use back where it belongs7 KB (1,057 words) - 23:21, 25 August 2023
- PCB Lab (section 2. Reset the Space)The PCB Lab has a specific organization to it. Put whatever you use back where it belongs. There is a place for everything and everything has a place. This9 KB (1,308 words) - 23:18, 25 August 2023
- Prototype Lab (section 2. Reset the Space)to cure liquid resin into a hard plastic. The Form 2 is the only 3D printer that the Prototype Lab has that is an SLA printer. It utilizes the Upside Down18 KB (2,851 words) - 19:50, 7 September 2023
- material. After the time at temperature has been set, the material should be placed between the platens and pressed for 2-3 seconds to remove any wrinkles. Now11 KB (1,610 words) - 23:41, 25 August 2023
- reworking process. The Air Bath has a power switch on the left, three buttons on the right, and a screen on the right. The switch has 3 positions which allows10 KB (1,478 words) - 00:00, 26 August 2023
- open during certain hours, so please view the Schedule below. The current Ace of the Tool Room is Mary Groom (mgroom19@georgefox.edu). View the most up-to-date2 KB (88 words) - 15:44, 22 May 2023
- Immediately inform the Aces of the Lab and/or Justin. What to do in the event of a spill: Evacuate the lab and shut it down until the spill has been properly cleaned8 KB (1,209 words) - 12:17, 23 January 2023
- Machine Shop has a specific organization to it. Put whatever you use back where it belongs. There is a place for everything and everything has a place. This8 KB (1,208 words) - 23:16, 25 August 2023
- Formlabs 3D Printer (redirect from Formlabs Form 2)print is under the approved cost/size cutoff ($7), or the person printing has special approval to exceed this limit. If a window pops up saying the print14 KB (1,983 words) - 13:09, 2 June 2023
- "tack" these same leads with solder - just to hold it. The rest of the video has great examples of IC's being soldered. Basic Soldering Lesson 8-9: We don't13 KB (1,534 words) - 00:03, 26 August 2023
- requires an account to use. Purge - Rapid printing of excess material which has been sitting in the machine lines for a long period of time. This helps ensure10 KB (1,239 words) - 23:53, 25 August 2023
- of material from the surface of the metal along an established line. This has great accuracy but only produces a thin line. Raster - Very similar to an12 KB (1,844 words) - 00:12, 26 August 2023
- sanding power down the dust collector and sander. 10. Make sure all motion has stopped before cleaning the machine. 11. Reset the space. Complete the Wood5 KB (667 words) - 00:23, 26 August 2023
- will also press the pin out after insertion. The pin has an outer diameter of .375" and the block has 4 holes that have been reamed to .374" The dowel pin12 KB (1,836 words) - 00:10, 26 August 2023
- the material because I'm cutting beyond 3/4" deep? 8. Has the proper program been loaded? 9. Has the Z-zero position been set using the material bed and18 KB (3,021 words) - 00:23, 26 August 2023
- if it is highly detailed and/or has holes that require fairly high tolerances. If it is a small, detailed part, a Form 2 printer should suffice. If the16 KB (2,591 words) - 23:48, 25 August 2023
- Make sure the bit has a bearing guide. 4. Verify the router is unplugged and place the router upside down on the bench. 5. Select the 1/2" or 1/4" collet9 KB (1,305 words) - 00:26, 26 August 2023