Search results
Jump to navigation
Jump to search
- scroll saw is simple machine with an oscillating blade. The thin shallow blade has a very narrow kerf and allows the user to cut fine details and sharp corners7 KB (1,030 words) - 00:30, 26 August 2023
- and cut out. Once cutting has been completed, it also needs to be reset and turned off. The student will choose a 2 in. x 2 in. graphic and upload into14 KB (2,182 words) - 23:46, 25 August 2023
- Don't try to adjust the out-feed table as the height has been set to support the material after it has been ran past the cutter head. Misalignment of the10 KB (1,559 words) - 14:57, 7 September 2023
- on Lathe 1 needs to be pulled out before being moved up and down. It also has a neutral position. The lever must be in neutral position for the machine7 KB (948 words) - 00:11, 26 August 2023
- are cutting has at least one straight edge and no nails or foreign objects. The straight edge will slide against the fence when ripping. 2. Measure the12 KB (1,986 words) - 00:30, 26 August 2023
- welding position. If you clamp the ground to the table make sure the work piece has good contact with the table near the ground clamp. The most difficult piece13 KB (2,048 words) - 00:35, 26 August 2023
- or Aligned route. Choose Simple if your board has no existing features, and choose Aligned if your board has some existing features. Lets go through the24 KB (3,603 words) - 23:56, 25 August 2023
- desired punch and release the lever while rocking the carousel to verify it has locked in place. Lift the bottom locking lever for the lower carousel and5 KB (690 words) - 00:17, 26 August 2023
- with division and cutting. The solid aluminum overarm has a 13 3/4" (350mm) throat and offers 5 1/2" (140mm) in height. The holder and wire coil (one spool12 KB (1,697 words) - 23:41, 25 August 2023
- machine contains a 1HP motor and has 10 different sanding spindles ranging from 1/4" to 4" in diameter. The cast iron table has an opening that provides clearance6 KB (904 words) - 00:28, 26 August 2023
- holes in wood. It has been programmed with various material and bit profiles to make setting the speed extremely simple. The current Ace of the Wood Drill9 KB (1,053 words) - 00:32, 26 August 2023
- capacitors) can retain a voltage/charge even after the power to a circuit has been cut. You can test voltages with a multimeter to ensure that the circuit29 KB (4,669 words) - 23:37, 25 August 2023
- designed for larger objects and has a larger field of view. When scanning, it works well to walk around the object while scanning. 2. Plug the desired scanner8 KB (1,212 words) - 23:23, 25 August 2023
- options for 2D a 360 on the left and Capture Settings on the right. You can select either 2D or 360 here. 2D will take one picture. The 2D Capture Mode19 KB (2,654 words) - 23:27, 25 August 2023
- mallet. Each method has its perks, so students will learn both methods. To show a complete knowledge of the press, the student will press 2 rivets by using10 KB (1,438 words) - 00:04, 26 August 2023
- surface can be maintained. When finished with the belt sander, make sure it has stopped spinning before setting it down. Never place it on the workpiece as6 KB (891 words) - 00:21, 26 August 2023
- and B, which control color. When each color has a 0 next to it, it will be fully black. When the red has a 255 next to it and the others have 0, it will28 KB (4,607 words) - 23:51, 25 August 2023
- length through the planer. Turn the Thickness Planer on and wait until it has reached full speed before starting to plane your stock. Only plane one piece10 KB (1,144 words) - 00:28, 26 August 2023
- program has a collision error, the paths are probably overlapping. try situating the i/o lines so that they do not overlap. If your program has a possible22 KB (3,398 words) - 00:19, 26 August 2023
- another chisel that is sharp. The wood lathe has few items that need to be maintained by the student or the Ace. Refer to the table below to see each procedure9 KB (1,241 words) - 00:33, 26 August 2023