Difference between revisions of "Jointer"

From maker-hub
Jump to navigation Jump to search
Line 48: Line 48:
 
====Operation====
 
====Operation====
  
Insert Text
+
The core of jointer consists of a round cutter head with many carbide inserts.  The cutter head is driven by an electric motor.  The table is made from multiple pieces to control the material being fed into the machine.  The front table can be adjusted up and down to control the amount of material that is exposed to the cutter head. The lower the table the more material per pass will be removed.  There are a few other things to keep in mind regarding your material as well. Make sure the material you are cutting is free of all foreign objects. Do not cut materials that may have nails or screws as they will damage the blade and may cause injury to you. Also, if the material contains a loose knot it can break free and create a safety hazard.
 +
 
 +
If your material looks good, the next step is to set up the jointer itself. When setting up the jointer table, make sure not to remove more than 1/16" of material. This limits the amount of cutter engagement and will help prevent a kickback. You will also want to hook up the adjacent dust collector to the end of the machine, make sure it is plugged in, and turned on. The dust collector must be used with the jointer to help keep the dust out of the air. As you make a cut, it is imperative that you keep the wood firmly against the fencea and tabe. Therefore, you should double check to see if you are reading the right measurement on the fence, especially because the fence can be moved to either side of the blade which is why there are two distance indicators, only one of which is correct for each set up. Make sure to ask the supervisor about the available jigs because they can be helpful for specialty cuts. Once the supervisor has demonstrated the use of a jig feel free to use it in the future but do not play around with jigs you are unfamiliar with.
 +
 
 +
After the saw is set up you are ready to cut. Turn on the saw and slowly push the material through, making sure to keep your hands away from the blade. Do not stop pushing the material until after the cut is finished unless there is an emergency, in which case, carefully use one hand or your hip to bump the off switch. Also not let go of your work piece during the cut or it will be forced back towards you.
 +
 
 +
Demonstration
  
 
====Demonstration====
 
====Demonstration====

Revision as of 10:14, 25 October 2019

Jointer icon
Powermatic Jointer

Make: Powermatic

Model: 54HH

Ace: Needed (Makerhub@georgefox.edu).

Location: Wood Shop

Description

The Powermatic jointer contains a 1HP motor and 6" capacity that will handle the most demanding work. The helical cutterhead provides quieter operation and finer finishing than conventional systems. The 4" dust port connects easily to any dust collector. Used to remove material from wood, as well as squaring to create straight pieces.

Here is an example of this piece of equipment being used.

Documentation

Terminology

  • Cutter Head - Drum of carbide inserts that performs the cutting.
  • Fence - Metal back-stop that is used to guide and control the angle of material being cut.

Product Home Page

User Manual

Training

Operation

The core of jointer consists of a round cutter head with many carbide inserts. The cutter head is driven by an electric motor. The table is made from multiple pieces to control the material being fed into the machine. The front table can be adjusted up and down to control the amount of material that is exposed to the cutter head. The lower the table the more material per pass will be removed. There are a few other things to keep in mind regarding your material as well. Make sure the material you are cutting is free of all foreign objects. Do not cut materials that may have nails or screws as they will damage the blade and may cause injury to you. Also, if the material contains a loose knot it can break free and create a safety hazard.

If your material looks good, the next step is to set up the jointer itself. When setting up the jointer table, make sure not to remove more than 1/16" of material. This limits the amount of cutter engagement and will help prevent a kickback. You will also want to hook up the adjacent dust collector to the end of the machine, make sure it is plugged in, and turned on. The dust collector must be used with the jointer to help keep the dust out of the air. As you make a cut, it is imperative that you keep the wood firmly against the fencea and tabe. Therefore, you should double check to see if you are reading the right measurement on the fence, especially because the fence can be moved to either side of the blade which is why there are two distance indicators, only one of which is correct for each set up. Make sure to ask the supervisor about the available jigs because they can be helpful for specialty cuts. Once the supervisor has demonstrated the use of a jig feel free to use it in the future but do not play around with jigs you are unfamiliar with.

After the saw is set up you are ready to cut. Turn on the saw and slowly push the material through, making sure to keep your hands away from the blade. Do not stop pushing the material until after the cut is finished unless there is an emergency, in which case, carefully use one hand or your hip to bump the off switch. Also not let go of your work piece during the cut or it will be forced back towards you.

Demonstration

Demonstration

Demonstrate you can safely setup the jointer. You will need to clean up one edge and one face of a board. Remember to never adjust the out feed table as it has been precisely set to the height of the cutter head. Adjusting the in-feed table will change the amount of material removed per pass. Do not set the in-feed table to remove more than 1/16" per pass. Your fingers should never go any lower than the height of the cutter guard. Verify the fence is locked and set at the angle needed before making a pass.

General Procedure

Edge Cleanup

1. Ensure that the material you are cutting is free from nails or foreign objects. Foreign material will damage the cutters and create flying hazards.

2. Make sure the board is at least 10" long and at least 3/8" wide to prevent the board from tilting while cutting.

3. Check the cut gauge on the front table. Make sure you know how much material is being removed. Never adjust the rear table.

4. Make sure the fence is tight and set at the correct angle

5. Check that the dust collector is connected.

6. Make sure the machine table is clear and press the power on switch for the jointer and dust collector.

7. Position your hands safely on the material and use a push stick if needed. A push stick is needed if your material is less than 2" thick. This will keep your fingers away from the cutter head.

8. Slowly feed the material through while pushing down on the table and back against the fence. Moving the material too fast will produce a poor finish.

9. After making a pass measure the material to see if another pass is required. Multiple passes are normally needed to get the desired results.

10. Power off the machine and dust collector.

11. Reset the space.

Facing Material (planing)

1. Ensure that the material you are cutting is free from nails or foreign objects. Foreign material will damage the cutters and create flying hazards.

2. Make sure the board is at least 10" long x 2" wide to prevent the board from tilting while facing.

3. Check the cut gauge. When facing you normally want to take off a small amount of material per pass due to the large surface area.

4. Make sure the fence is tight and set at the correct angle

5. Check that the dust collector is connected.

6. Make sure the machine table is clear and press the power on switch for the jointer and dust collector.

7. Position your hands safely on the material. A push stick is needed if your material is less than 2" thick. This will keep your fingers away from the cutter head.

8. Slowly feed the material through on the table to get a smooth finish.

9. After making a pass inspect the material to see if another pass is needed. Multiple passes are normally required to get the desired results.

10. Power off the machine and dust collector.

11. Reset the space.

Safety

There are several hazards you need to be aware of when using a jointer.

  • The cutters are very sharp and spin very fast. Keep your fingers away from the cutter head even when its not spinning. Use a push pad/stick to keep your fingers a safe distance from the cutters.
  • Never let your thumb or fingers hang down near the table when pushing a board through the machine.
  • Hold onto material firmly and keep it against the table and fence to help prevent material kicking back. If material catches on the blade the material can shoot back at you and this is called a kickback.
  • Use a hold down or push block when surfacing stock less than 12" long, or 3 inches wide, or 3 inches thick.
  • Never feed material backwards.
  • Never try to cut across grain as this could cause a kickback.
  • Don't exceed 1/16" cut per pass.

This is a video showing how to safely use the jointer:

Certification

Foxtale Course

Troubleshooting

If the finish looks rough you may be feeding the material too fast. Try slowing down the speed you are feeding the material through.

Maintenance

General maintenance

Carbide cutters need rotating when they start to dull. This is a job for the technician.

Specific Maintenance Tasks

Maintenance Procedure Frequency Done By
Sample Sample Sample