Difference between revisions of "Table Saw"
| Line 57: | Line 57: | ||
2. Measure the width of the board and determine the width of cut desired. | 2. Measure the width of the board and determine the width of cut desired. | ||
| − | 3. Lift the locking handle on the fence and slide the fence to | + | 3. Lift the locking handle on the fence and slide the fence to the desired cut width using the scale. Make sure you use the scale for the correct side of the blade. |
4. Lock the fence by pressing down on the locking handle. | 4. Lock the fence by pressing down on the locking handle. | ||
| − | 5. Use the blade lift handle on the front of the saw to set the height of the blade approximately 1 tooth above the height of the material. | + | 5. Use the blade lift handle on the front of the saw to set the height of the blade approximately 1 tooth above the height of the material by placing the material next to the blade. This limits the exposed blade. |
| − | 6. Turn on the power switch on the front of the saw and the dust collector. The green light on the saw will flash and turn solid when the saw | + | 6. Turn on the power switch on the front of the saw and the dust collector. The green light on the saw will flash and turn solid green when the saw is ready. |
| − | 7. Make sure nothing is touching the blade. Turn on the saw by gently pulling on the paddle switch located on the front of the machine. The paddle switch is also the off switch. | + | 7. Make sure nothing is touching the blade. Turn on the saw by gently pulling on the red paddle switch located on the front of the machine. The paddle switch is also the off switch when pressed. |
8. Line up the flat side of the material with the fence without touching the blade. The fence is a guide and the material should be pressed firmly into the fence as well as down on the table. | 8. Line up the flat side of the material with the fence without touching the blade. The fence is a guide and the material should be pressed firmly into the fence as well as down on the table. | ||
| Line 75: | Line 75: | ||
11. It is helpful to have someone assisting on the back side of the saw to help hold material being fed off the table. | 11. It is helpful to have someone assisting on the back side of the saw to help hold material being fed off the table. | ||
| − | 12. When | + | 12. When the saw cut is complete, press in on the paddle switch to turn off the saw. |
| + | |||
| + | 13. Move the fence off to the side by lifting the brake handle and sliding the fence off to the side. | ||
| + | |||
| + | 14. Place the cross cut sled on the table by aligning the table slots with the rails on the sled. | ||
| + | |||
| + | 15. Slide the sled over the blade and use the material to set the blade height using the blade height handle on the front of the saw. The blade should be roughly one tooth taller than the top of the material. | ||
| + | |||
| + | 16. Place the material flat edge against the back of the sled and align the material with the edge of the blade. | ||
| + | |||
| + | 17. Once the blade is clear pull the red paddle switch to turn on the saw. | ||
| + | |||
| + | 18. Slide the sled forward to cut through the material at the desired location. | ||
| + | |||
| + | 19. Slide the sled back to you so it clears the blade. | ||
| + | |||
| + | 20. Power down the saw by pressing the red paddle switch located on the front of the machine. | ||
| + | |||
| + | 21. Lower the blade below the table using the crank handle on the front of the machine | ||
==Certification== | ==Certification== | ||
Revision as of 10:33, 11 June 2019
Make: SawStop
Model: PCS31230
Ace: Needed (Makerhub@georgefox.edu).
Location: Wood Shop
Description
The SawStop table saw is a top of the line cabinet saw built for top quality work and safety. Used for many things, the table saw is a fundamental part of any woodshop. The SawStop safety system is a top of the line design produced to make the machine as safe as possible. A unique cartridge is in the machine. At the slightest hint of conductivity like a finger would give off, the cartridge fires and jams into the path of the blade. The blade is then dropped down into the body of the saw to prevent accidentally hitting it again. All this happens within 5 milliseconds, helping to ensure users stay safe. **This is NOT an excuse to ignore the 3 commandments and safety rules. Merely a way to help safety in case of accident.
The table saw is usually used for cutting long rips out of wood. A basic first step for getting wood down to size lengthwise. A fence is used to keep the piece straight when pushing through the saw. While the saw is usually used for cutting the long side of a piece of wood, jigs and tools are available for doing cross-cuts on the table saw as well. These are used to make sure the wood stays solidly in place as it’s pushed through and to keep it straight.
Documentation
Terminology
- Rip - Cuts made along the length of the wood
- Cross-cut - Cuts made across the grain along the shorter side of the wood
- Push stick - A piece of wood or plastic used to push the wood being cut through the blade while keeping fingers away from the blade
- Fence - A guide for measuring the cut and guiding the wood
Training
Overview
Insert Text
General Use
Insert text
Demonstration
Demonstrate you can safely setup the saw and rip a board. You will then proceed to cross cut one of the remaining piece.
1. Ensure that the material you are cutting has at least one straight edge and no nails or foreign objects. The straight edge will slide against the fence when ripping.
2. Measure the width of the board and determine the width of cut desired.
3. Lift the locking handle on the fence and slide the fence to the desired cut width using the scale. Make sure you use the scale for the correct side of the blade.
4. Lock the fence by pressing down on the locking handle.
5. Use the blade lift handle on the front of the saw to set the height of the blade approximately 1 tooth above the height of the material by placing the material next to the blade. This limits the exposed blade.
6. Turn on the power switch on the front of the saw and the dust collector. The green light on the saw will flash and turn solid green when the saw is ready.
7. Make sure nothing is touching the blade. Turn on the saw by gently pulling on the red paddle switch located on the front of the machine. The paddle switch is also the off switch when pressed.
8. Line up the flat side of the material with the fence without touching the blade. The fence is a guide and the material should be pressed firmly into the fence as well as down on the table.
9. Slowly feed the material in towards the blade while keeping your fingers clear of the blade. Use a push stick to keep your fingers away from the blade.
10. Make sure you keep a firm hold on the material and do not stop feeding the material until it has passed beyond the blade.
11. It is helpful to have someone assisting on the back side of the saw to help hold material being fed off the table.
12. When the saw cut is complete, press in on the paddle switch to turn off the saw.
13. Move the fence off to the side by lifting the brake handle and sliding the fence off to the side.
14. Place the cross cut sled on the table by aligning the table slots with the rails on the sled.
15. Slide the sled over the blade and use the material to set the blade height using the blade height handle on the front of the saw. The blade should be roughly one tooth taller than the top of the material.
16. Place the material flat edge against the back of the sled and align the material with the edge of the blade.
17. Once the blade is clear pull the red paddle switch to turn on the saw.
18. Slide the sled forward to cut through the material at the desired location.
19. Slide the sled back to you so it clears the blade.
20. Power down the saw by pressing the red paddle switch located on the front of the machine.
21. Lower the blade below the table using the crank handle on the front of the machine
Certification
Foxtale Quiz
Troubleshooting
Maintenance
General maintenance
Insert text
Specific Maintenance Tasks
| Maintenance Procedure | Frequency | Done By |
|---|---|---|
| Sample | Sample | Sample |