Changes

Jump to navigation Jump to search
no edit summary
Line 43: Line 43:  
==Training==
 
==Training==
 
====Overview====
 
====Overview====
Before a cut can be performed with the handheld CNC router you must provide a cut design in the form of an SVG file. These can be created in several different programs but Inkscape is recommended because it is installed on the hub computers and is free to download onto a personal device. When designing your cut use the actual dimensions of the cut. If it is your first time using Inkscape there are tutorials on [https://inkscape.org/learn/tutorials/ their website] and [https://www.youtube.com/channel/UCEQXp_fcqwPcqrzNtWJ1w9w Youtube] as well. After you have created the cut file transfer it to the router using a USB drive or by uploading it over WiFi. Take the CNC out of the box, set it on a flat, wooden surface, and plug it in. Ensure that the dust collection vacuum is working and has a good seal on the CNC connecting piece. You should never use the CNC without dust collection working! Determine the area on the wood material that you want to cut on and place several strips of tape a bit beyond the width and height of the area you’ll need, with 4-6 inch separation between the tape strips (they don’t need to be straight and parallel, they can be crooked). The CNC uses this tape to manage the CNC’s position. Double check that the correct router bit is secure and in place in the spindle. If the router bit needs to be replaced or secured, make sure that the spindle is turned off and unplugged from the main computer of the router before you take the spindle out of its place. Keep in mind that the switch for the spindle only turns off the spindle, not the CNC computer system.  On the touch interface, select the scan mode and create a new scan for the tape. Move the CNC around the surface until all of the (unripped) tape is highlighted blue. It is important to have enough tape, if the CNC loses track of enough tape it will immediately raise the spindle and stop the router from cutting any material. Once you’re ready, go to the cut menu on the CNC’s touch interface and select the correct diameter for your router bit and the depth your want to cut at. It will ask you to “touch off”, select yes. Touching off means that the CNC will lower the router until it just touches the surface in order to calibrate the depth control for the router. Select the appropriate cut type (inside, outside, on-line, or pocket) for the cut you will be making. The pocket cut type will cut out the entire area of the shape you have selected. The guide cut type will not act as a cutting line, it will only show on the display as a reference. You can preview the cut size and direction by looking at the direction of the dashed outline and the thicker, grey line on top of the small, dashed line. Double check that the spindle speed (the control wheel to the right of the spindle) is set correctly. Before you make your first cut, double check the tape accuracy by moving the CNC around and watching the tape icon on the top-right of the display. This shows how much tape is visible to the camera, so the more full the tape bar is the better. If it is consistently low, it may be best to add more tape and do a new scan. Once these things have been completed, you should be good to go for cutting! Keep in mind that you may have to do multiple passes to get the right depth and you may also have to change cut type depending on what kind of cut you’re trying to make.
+
Before a cut can be performed with the handheld CNC router you must provide a cut design in the form of an SVG file. These can be created in several different programs but Inkscape is recommended because it is installed on the hub computers and is free to download onto a personal device. When designing your cut use the actual dimensions of the cut. If it is your first time using Inkscape there are tutorials on [https://inkscape.org/learn/tutorials/ their website] and [https://www.youtube.com/channel/UCEQXp_fcqwPcqrzNtWJ1w9w Youtube] as well. Alterativly, you can download SVG from a website like [https://thenounproject.com/ this]. After you have created the cut file transfer it to the router using a USB drive or by uploading it over WiFi. Take the CNC out of the box, set it on a flat, wooden surface, and plug it in. Ensure that the dust collection vacuum is working and has a good seal on the CNC connecting piece. You should never use the CNC without dust collection working! Determine the area on the wood material that you want to cut on and place several strips of tape a bit beyond the width and height of the area you’ll need, with 4-6 inch separation between the tape strips (they don’t need to be straight and parallel, they can be crooked). The CNC uses this tape to manage the CNC’s position. Double check that the correct router bit is secure and in place in the spindle. If the router bit needs to be replaced or secured, make sure that the spindle is turned off and unplugged from the main computer of the router before you take the spindle out of its place. Keep in mind that the switch for the spindle only turns off the spindle, not the CNC computer system.  On the touch interface, select the scan mode and create a new scan for the tape. Move the CNC around the surface until all of the (unripped) tape is highlighted blue. It is important to have enough tape, if the CNC loses track of enough tape it will immediately raise the spindle and stop the router from cutting any material. Once you’re ready, go to the cut menu on the CNC’s touch interface and select the correct diameter for your router bit and the depth your want to cut at. It will ask you to “touch off”, select yes. Touching off means that the CNC will lower the router until it just touches the surface in order to calibrate the depth control for the router. Select the appropriate cut type (inside, outside, on-line, or pocket) for the cut you will be making. The pocket cut type will cut out the entire area of the shape you have selected. The guide cut type will not act as a cutting line, it will only show on the display as a reference. You can preview the cut size and direction by looking at the direction of the dashed outline and the thicker, grey line on top of the small, dashed line. Double check that the spindle speed (the control wheel to the right of the spindle) is set correctly. Before you make your first cut, double check the tape accuracy by moving the CNC around and watching the tape icon on the top-right of the display. This shows how much tape is visible to the camera, so the more full the tape bar is the better. If it is consistently low, it may be best to add more tape and do a new scan. Once these things have been completed, you should be good to go for cutting! Keep in mind that you may have to do multiple passes to get the right depth and you may also have to change cut type depending on what kind of cut you’re trying to make.
    
====Demonstration====
 
====Demonstration====
Line 50: Line 50:     
====General Procedure====
 
====General Procedure====
Once this has been done, unscrew the bolt on the right of the spindle just loose enough to remove the spindle. To remove the router bit, press down on the locking mechanism and twist the collet until the router bit can be removed. Make sure that the router bit grooves are not below a quarter inch from the top of the collet. Once a new router bit has been put in place, use the wrench to tighten the collet. Reinsert the spindle into the slot on the CNC and tighten the bolt “finger tight”. At this point, the CNC is set up and ready to go, it is time to scan the tape.
+
Included in this section are some helpful videos made by Shaper that walk through the entire process of using the router. It is highly recommended that you look through the videos but if you do not then there are instructions walking through the same process.
 
  −
Creating Cut Files:
  −
 
  −
[https://thenounproject.com/ Sample SVGs]
  −
 
  −
[https://support.shapertools.com/hc/en-us/articles/115003368954-Inkscape-Issues How to use Inkscape]
      
Setting up the Cut Area:
 
Setting up the Cut Area:
 
{{#evu:https://www.youtube.com/watch?v=sdsMOPZFMRQ}}
 
{{#evu:https://www.youtube.com/watch?v=sdsMOPZFMRQ}}
 +
# Remove the router and from its box.
 +
# Power on the router. This machine has the capability to connect to the WiFi so that cut files can be loaded onto the machine from an individual's Shaper account. However, this is a hassle and it is easier to use a Usb drive to transfer files to the machine.
 +
#
 +
* Open box
 +
* Take the CNC out and set on cutting surface
 +
* Plug in dust collection system
 +
*# Verify it works
 +
* Place the tape on the cutting surface
 +
* Verify you have the correct router bit attached
 +
* Plug the power cord into a wall outlet
 +
* Create a new scan of the tape
 +
* Select your drawing and place it
 +
* Adjust the cut depth and router diameter
 +
*# Touch off
 +
* Trace the cut outline and verify that tape visibility is good
 +
* Cut
 +
* Reset the space when finished
    
Performing a Cut:
 
Performing a Cut:
 
{{#evu:https://www.youtube.com/watch?v=DekAjAOIVvQ}}
 
{{#evu:https://www.youtube.com/watch?v=DekAjAOIVvQ}}
 +
 +
Once this has been done, unscrew the bolt on the right of the spindle just loose enough to remove the spindle. To remove the router bit, press down on the locking mechanism and twist the collet until the router bit can be removed. Make sure that the router bit grooves are not below a quarter inch from the top of the collet. Once a new router bit has been put in place, use the wrench to tighten the collet. Reinsert the spindle into the slot on the CNC and tighten the bolt “finger tight”. At this point, the CNC is set up and ready to go, it is time to scan the tape.
    
==Safety==
 
==Safety==
473

edits

Navigation menu