Changes

### Voltera will ask you to upload your Ink and Hole files. Remember, the correct Hole file will say Plated in the name. This will allow you to calibrate the Voltera later and it supplies the drill locations.

### Voltera will ask you to upload your Ink and Hole files. Remember, the correct Hole file will say Plated in the name. This will allow you to calibrate the Voltera later and it supplies the drill locations.

### Then it will ask you to move your boards location on the plate so the Voltera knows where it needs to drill. This is the sketchy part. It outlines a square, and you make a judgement based on what it thinks. If it outlines too low, move your circuit up further on the plate to compensate for it. If it outlines too far to the left, move your circuit to the right on the plate to compensate for it. Continue this process until it looks "good enough."

### Then it will ask you to move your boards location on the plate so the Voltera knows where it needs to drill. This is the sketchy part. It outlines a square, and you make a judgement based on what it thinks. If it outlines too low, move your circuit up further on the plate to compensate for it. If it outlines too far to the left, move your circuit to the right on the plate to compensate for it. Continue this process until it looks "good enough."

### Clean the calibration switches. Do not drench the Q-tip with Isopropyl alcohol, only get damp, and wipe away gently. Use the clamps and screws to secure your board. It would be such a shame if it moved during fabrication... <figure-inline class="mw-default-size">[[File:Board.jpg|300x300px]]</figure-inline>

### Clean the calibration switches. Do not drench the Q-tip with Isopropyl alcohol, only get damp, and wipe away gently. Use the clamps and screws to secure your board. It would be such a shame if it moved during fabrication... <figure-inline class="mw-default-size"><figure-inline>[[File:Board.jpg|300x300px]]</figure-inline></figure-inline>

### Mount the probe on machine. This will help us calibrate the machine. It will move to the wrong spot initially, but then it is your duty to move the probe into the correct spot. Lowering the probe will allow you to make fine tune movements to optimize the alignment.[[File:Voltera mount_probe.jpg|border|none|300x300px]]

### Mount the probe on machine. This will help us calibrate the machine. It will move to the wrong spot initially, but then it is your duty to move the probe into the correct spot. Lowering the probe will allow you to make fine tune movements to optimize the alignment.[[File:Voltera mount_probe.jpg|border|none|300x300px]]

### Once the alignment is complete, it will measure the height of every part of the board. It will take a couple minutes, so just be patient.  

### Once the alignment is complete, it will measure the height of every part of the board. It will take a couple minutes, so just be patient.  

### Once that is complete, it is time to select the holes we want to drill. '''All the holes you select are highlighted in Green.''' Remove the probe and select which holes you want to drill. Remember not to drill the holes that already exist!<figure-inline class="mw-default-size">[[File:...holes.png|300x300px]]</figure-inline>

### Once that is complete, it is time to select the holes we want to drill. '''All the holes you select are highlighted in Green.''' Remove the probe and select which holes you want to drill. Remember not to drill the holes that already exist!<figure-inline>[[File:...holes.png|300x300px]]</figure-inline>

###Select the corresponding drill bit, put it into the drill, mount it, and plug it in. Be extra careful not to break anything. People usually break it because while they are mounting it, the drill hits the Voltera and snaps. It's okay to push it into the drill pretty far, and this will keep you from breaking it. '''DON'T FORGET TO USE THE ALLEN WRENCH TO SECURE THE BIT!''' <figure-inline class="mw-default-size">[[File:Bist.jpg|300x300px]]</figure-inline>

###Select the corresponding drill bit, put it into the drill, mount it, and plug it in. Be extra careful not to break anything. People usually break it because while they are mounting it, the drill hits the Voltera and snaps. It's okay to push it into the drill pretty far, and this will keep you from breaking it. '''DON'T FORGET TO USE THE ALLEN WRENCH TO SECURE THE BIT!'''  

### The drill should sing you a little song once it's connected. '''Before drilling, prepare the vacuum.''' Use this to suck all the debris that comes from your board. You can get it decently close to the board, even on the board while it is drilling, just be sure to move when the drill is getting ready to move.

### The drill should sing you a little song once it's connected. '''Before drilling, prepare the vacuum.''' Use this to suck all the debris that comes from your board. You can get it decently close to the board, even on the board while it is drilling, just be sure to move when the drill is getting ready to move.[[File:VacuumBoi.jpg|none|thumb]]

### And you're finished drilling holes! Vacuum up any debris and continue with laying the traces.

### And you're finished drilling holes! Vacuum up any debris and continue with laying the traces.

## Drilling for an Aligned Board

## Drilling for an Aligned Board