Changes

Setting up a Cut:

Setting up a Cut:

# First off, to get your design, just copy an image and paste it into CorelDraw or find a pdf version of the file and open it. If you are cutting a part from a Solidworks file it must be saved as a dxf before importing to CorelDraw.   

# First off, to get your design, just copy an image and paste it into CorelDraw or find a pdf version of the file and open it. If you are cutting a part from a Solidworks file it must be saved as a dxf before importing to CorelDraw.   

# Measure the size of your material, and set the page in CorelDRAW to those dimensions. You can alter the dimensions of the page you are putting the image on, and even the image itself in the top left. If you want to keep the image dimensions consistent, but just scale it down, click the lock button to the right of these dimensions. If you want to make your own design using text, squares, circles, etc, you can find everything you need in the column on the far left of the client.[[File:Image.png|thumb|827x827px|none]]

# Measure the size of your material, and set the page in CorelDRAW to those dimensions. You can alter the dimensions of the page you are putting the image on, and even the image itself in the top left. If you want to keep the image dimensions consistent, but just scale it down, click the lock button to the right of these dimensions. If you want to make your own design using text, squares, circles, etc, you can find everything you need in the column on the far left of the client.[[File:Image.png|thumb|827x827px|none]]

# Once you have your design, we need to alter the colors a little bit so the Laser Cutter can understand what you want it to do. It goes like this: a red line with a hairline thickness will cut, and anything that is black will engrave.  

# Once you have your design, we need to alter the colors a little bit so the Laser Cutter can understand what you want it to do. It goes like this: a red line with a hairline thickness will cut, and anything that is black will engrave.  

Setting up the Laser Cutter:

Setting up the Laser Cutter:

# Turn on the machine using the power switch located on the back of the machine in the left corner. The machine will go through a startup procedure where the cutting bed  

# Turn on the machine using the power switch located on the back of the machine in the left corner. The machine will go through a startup procedure where the cutting bed lowers and the laser travels to its home position. Note that the lid must be closed for the startup procedure to begin There will be some beeping coming 

#  

#  

# Alright, now it’s time to focus the laser onto your material. On the left of the Laser Cutter, there is its filter with a similar color scheme that looks like its nephew. On top of that will be a piece of metal that is shown below, this is the focusing tool. This mounts on the right side of the laser and sets the material a certain distance from the laser. Put your material in the top left of the Honeycomb Table, mount the focusing tool on the right side of the laser, then begin raising the table. The moment the focusing tool falls of from hitting your material, stop raising the table. Be sure to slow down toward the end of the process to assure the laser does not get too close to your material. You can then use the controls to put the laser at the top left of your material (assuming it is square). This keeps you and others from being idiots and wasting material.

# Alright, now it’s time to focus the laser onto your material. On the left of the Laser Cutter, there is its filter with a similar color scheme that looks like its nephew. On top of that will be a piece of metal that is shown below, this is the focusing tool. This mounts on the right side of the laser and sets the material a certain distance from the laser. Put your material in the top left of the Honeycomb Table, mount the focusing tool on the right side of the laser, then begin raising the table. The moment the focusing tool falls of from hitting your material, stop raising the table. Be sure to slow down toward the end of the process to assure the laser does not get too close to your material. You can then use the controls to put the laser at the top left of your material (assuming it is square). This keeps you and others from being idiots and wasting material.