124
edits
Changes
Jump to navigation
Jump to search
Line 1:
Line 1: − [[{{#show: {{FULLPAGENAME}}|?Has icon|link=none}}|100px|left|top|{{#show: {{FULLPAGENAME}}|?Has icondesc}}]] Line 12:
Line 11: − + − + − + − + − + + + + + + + + + + + + + + Line 48:
Line 60: − <br>+ − * [https://www.teknatool.com/wp-content/uploads/2018/11/833-Voyager-Drill-Press-Manual-FINAL-version-20.Jul_.2018.pdf User Manual] − + Line 76:
Line 87: − + − + − + − + − + − #### Set handle fully back down in place on screw − #### Tighten further until snug and quill is locked in place − + Line 98:
Line 107: − − ==Safety== − * Make sure you are wearing proper attire. (Safety Glasses, Short Sleeves, Closed Toed Shoes, No jewelry or any loose hanging accessories, and hair that is longer than collar-length tied up) − * Keep body parts or anything else other than the workpiece out of the path of the drill bit when on. − * Do not move workpiece while drill bit is inside of workpiece. − * Make sure the drill bit is secure and fastened into the chuck. − * Make sure drill is at the appropriate speed. − * Keep work piece secure so it can't rotate. If the work is long enough it should stick out to the left side of the operator against the vertical column to prevent rotation. − + Line 147:
Line 148: − + − +
no edit summary
[[{{#show: {{FULLPAGENAME}}|?Has image|link=none}}|300px|thumb|upright=1.5|{{#show: {{FULLPAGENAME}}|?Has imagedesc}}]]
[[{{#show: {{FULLPAGENAME}}|?Has image|link=none}}|300px|thumb|upright=1.5|{{#show: {{FULLPAGENAME}}|?Has imagedesc}}]]
|Has imagedesc=Nova Voyager dvr Drill Press
|Has imagedesc=Nova Voyager dvr Drill Press
|Has description=
|Has description=
|Has certification=
|Has certification=https://georgefox.instructure.com/courses/1266
|Has group=Woodworking
|Has group=Woodworking
|Has make=Nova
|Has make=Tenka Tool
|Has model=Voyager DVR
|Has model=Nova Voyager DVR
|Has ace=John Phifer;jphifer17@georgefox.edu
|Has serial number=301545
}}
|Has ace=Needed;Needed
}}[[{{#show: {{FULLPAGENAME}}|?Has icon|link=none}}|140px|left|top|{{#show: {{FULLPAGENAME}}|?Has icondesc}}]]
Make: {{#show: {{PAGENAME}} |?Has make}}
Make: {{#show: {{PAGENAME}} |?Has make}}
Model: {{#show: {{PAGENAME}} |?Has model}}
Model: {{#show: {{PAGENAME}} |?Has model}}
Serial Number: {{#show: {{PAGENAME}} |?Has serial number}}
Ace: {{#show: {{PAGENAME}} |?Has ace.Has name}} ({{#show: {{PAGENAME}} |?Has ace.Has email address}}).
Ace: {{#show: {{PAGENAME}} |?Has ace.Has name}} ({{#show: {{PAGENAME}} |?Has ace.Has email address}}).
Location: {{#show: {{PAGENAME}} |?Is located in facility}}
Location: {{#show: {{PAGENAME}} |?Is located in facility}}
__TOC__
__TOC__
==Safety First==
[[File:Safety First HD2.png|left|150px]]
* Make sure you are wearing proper attire. (Safety Glasses, Short Sleeves, Closed Toed Shoes, No jewelry or any loose hanging accessories, and hair that is longer than collar-length tied up)
* Keep body parts or anything else other than the workpiece out of the path of the drill bit when on.
* Do not move workpiece while drill bit is inside of workpiece.
* Make sure the drill bit is secure and fastened into the chuck.
* Make sure drill is at the appropriate speed.
* Keep work piece secure so it can't rotate. If the work is long enough it should stick out to the left side of the operator against the vertical column to prevent rotation.
==Description==
==Description==
'''Feed Handle''' - a rotating three-pronged handle used to set the depth of the drill bit.<br>
'''Feed Handle''' - a rotating three-pronged handle used to set the depth of the drill bit.<br>
[[Media:833-Voyager-Drill-Press-Manual-FINAL-version-20.Jul .2018.pdf|Wood Drill Press User Manual]]
==Training==
==Training==
====Overview====
====Operation====
The Wood Drill Press is mainly used for drilling holes into wood.
The Wood Drill Press is mainly used for drilling holes into wood.
### Tilt table to desired angle.
### Tilt table to desired angle.
### Re-tighten bolt and set screw, and ensure table is securely locked in place before drilling.
### Re-tighten bolt and set screw, and ensure table is securely locked in place before drilling.
## For blind holes, lock the table at desired depth:
## For blind holes, use the depth stop to stop the drill bit at the desired depth.
### To lock the quill at a certain depth, pull the quill lever down to the desired level and turn the quill lock handle clockwise and tighten firmly.
### Adjust the depth stop by rotating it until it is at the desired height.
### If the quill lock handle is not fully tightened when it reaches its limit:
#### For large adjustments, pressing the button on the depth stop enables it to move up and down freely.
#### Pull the handle out along the screw so it freely rotates ['''Note: clarify where the "screw" is and what its function is.]'''
### The lever to the right of the spindle may be used to lock the drill bit at a desired depth while you adjust the depth stop. (i.e. lock the drill bit at the depth you want, then move the depth stop to the corresponding position.)
#### Rotate back counter-clockwise
#### Remember to unlock the lever prior to drilling.
# Line piece up with drill bit and fasten down onto work table using a clamp or vice. If drilling a through hole, put a piece of FLAT scrap wood under the piece being drilled to avoid a blowout.
# Line piece up with drill bit and fasten down onto work table using a clamp or vice. If drilling a through hole, put a piece of FLAT scrap wood under the piece being drilled to avoid a blowout.
# Turn power on using switch located on the right side of the machine as shown in the picture below. The yellow tab must be in place for the drill to be powered on.[[File:...voyagerthing.png|none|thumb]]
# Turn power on using switch located on the right side of the machine as shown in the picture below. The yellow tab must be in place for the drill to be powered on.[[File:...voyagerthing.png|none|thumb]]
# Now the display screen should be on. Using the buttons, adjust the speed to the correct specifications needed to cut the material using the built-in computer. '''[Need to show illustration of display screen with description of settings - CZ]'''
# Now the display screen should be on. Using the buttons, adjust the speed to the correct specifications needed to cut the material using the built-in computer.
## To use the speed chart:
## To use the speed chart:
### Go to the Menu > Speed Chart.
### Go to the Menu > Speed Chart.
# When done, remove drill bit. ( When loose, use one hand to unscrew and the other to hole the drill bit, so the drill bit does not fall and get damaged.)
# When done, remove drill bit. ( When loose, use one hand to unscrew and the other to hole the drill bit, so the drill bit does not fall and get damaged.)
# When done, return all burrowed equipment and clean work area.
# When done, return all burrowed equipment and clean work area.
==Certification==
==Certification==
[https://foxtale.georgefox.edu/moodle/course/view.php?id=31323 Foxtale Quiz]
[https://georgefox.instructure.com/courses/1266 Canvas Quiz]
==Troubleshooting==
==Troubleshooting==
* [https://www.teknatool.com/product/nova-voyager-dvr-variable-speed-drill-press-exclusive-amazon-bundle/?gclid=EAIaIQobChMI4PzDxsni2wIVFNNkCh3lBAcLEAAYASAAEgL5NvD_BwE Product Home Page]
* [https://www.teknatool.com/product/nova-voyager-dvr-variable-speed-drill-press-exclusive-amazon-bundle/?gclid=EAIaIQobChMI4PzDxsni2wIVFNNkCh3lBAcLEAAYASAAEgL5NvD_BwE Product Home Page]
* <figure-inline class="mw-default-size">[[File:wood_drill_press_operation_manual|220x220px]]
* <figure-inline class="mw-default-size"><figure-inline><figure-inline><figure-inline><figure-inline>[[File:wood_drill_press_operation_manual|220x220px]]</figure-inline></figure-inline></figure-inline></figure-inline>
* [https://www.youtube.com/watch?v=6PvDExhAOC8 First look]
* [https://www.youtube.com/watch?v=6PvDExhAOC8 First look]
== Training ==
== Training ==
* <figure-inline class="mw-default-size">[[File:wood_drill_press_operation_manual|220x220px]]
* <figure-inline class="mw-default-size"><figure-inline><figure-inline><figure-inline><figure-inline>[[File:wood_drill_press_operation_manual|220x220px]]</figure-inline></figure-inline></figure-inline></figure-inline>
<br /><br /><br /><br /><br />
<br /><br /><br /><br /><br />