2,297
edits
Changes
Jump to navigation
Jump to search
Line 3:
Line 3: + + Line 14:
Line 16: − + − + Line 22:
Line 24: + + + Line 49:
Line 54: − + + − + Line 87:
Line 93: − + − + Line 113:
Line 119: − + Line 121:
Line 127: − +
→User Manuals
|Has make=OMAX
|Has make=OMAX
|Has model=ProtoMAX
|Has model=ProtoMAX
|Has serial number=8100202
|Has name={{PAGENAME}}
|Has name={{PAGENAME}}
|Is located in facility= Machine Shop
|Is located in facility= Machine Shop
|Is used in domain=
|Is used in domain=
|Has certification=https://georgefox.instructure.com/courses/1303
|Has function=
|Has function=
|Has icon=File:waterjet_cutter_icon.png
|Has icon=File:waterjet_cutter_icon.png
|Has description=Used for precision cutting of tough materials.
|Has description=Used for precision cutting of tough materials.
|Has QR code=
|Has QR code=
|Has ace=Donald Williams;dwilliams16@georgefox.edu
|Has ace=Needed;Needed
}}
}}
[[{{#show: {{FULLPAGENAME}}|?Has icon|link=none}}|100px|left|top|{{#show: {{FULLPAGENAME}}|?Has icondesc}}]]
[[{{#show: {{FULLPAGENAME}}|?Has icon|link=none}}|140px|left|top|{{#show: {{FULLPAGENAME}}|?Has icondesc}}]]
[[{{#show: {{FULLPAGENAME}}|?Has image|link=none}}|300px|thumb|upright=1.5|{{#show: {{FULLPAGENAME}}|?Has imagedesc}}]]
[[{{#show: {{FULLPAGENAME}}|?Has image|link=none}}|300px|thumb|upright=1.5|{{#show: {{FULLPAGENAME}}|?Has imagedesc}}]]
Model: {{#show: {{PAGENAME}} |?Has model}}
Model: {{#show: {{PAGENAME}} |?Has model}}
Serial Number: {{#show: {{PAGENAME}} |?Has serial number}}
Ace: {{#show: {{PAGENAME}} |?Has ace.Has name}} ({{#show: {{PAGENAME}} |?Has ace.Has email address}}).
Ace: {{#show: {{PAGENAME}} |?Has ace.Has name}} ({{#show: {{PAGENAME}} |?Has ace.Has email address}}).
Location: {{#show: {{PAGENAME}} |?Is located in facility}}
Location: {{#show: {{PAGENAME}} |?Is located in facility}}
__TOC__
__TOC__
==== User Manuals ====
==== User Manuals ====
[https://knowledgebase.omax.com/protomax/content/accessories-home.htm?tocpath=MANUALS%7CACCESSORY%20%20GUIDES%7C_____0 Complete list of ProtoMAX manuals]
[[Media:Waterjet Cutter ProtoMAX Manual.pdf|Waterjet Cutter User Manual]]
==Training==
==Training==
====Overview====
====Operation====
The waterjet cutter is an amazing tool that can be used on a wide variety of materials including 1" steel! However, it is limited to a 12" by 12" cut area with a 1" thickness being its maximum. Make sure the waterjet cutter is capable of handling your part and your material before going through all of the setup procedures. Like cutting many other two dimensional cutting tools, the cutting process should begin with a DXF file created from Solidworks or a similar software. Once a DXF fie has been created it can then be used to create a tool path using ProtoMAX LAYOUT. The detailed steps to do do this can be found in the general procedure but the most important step is to ensure that the waterjet pierces the material outside of the part outline. After the tool path is created and the machine has been properly set up, the job can be posted to the MAKE software, which is installed on the waterjet's laptop computer, to perform the cut.
The waterjet cutter is an amazing tool that can be used on a wide variety of materials including 1" steel! However, it is limited to a 12" by 12" cut area with a 1" thickness being its maximum. Make sure the waterjet cutter is capable of handling your part and your material before going through all of the setup procedures. Like cutting many other two dimensional cutting tools, the cutting process should begin with a DXF file created from Solidworks or a similar software. Once a DXF fie has been created it can then be used to create a tool path using ProtoMAX LAYOUT. The detailed steps to do do this can be found in the general procedure but the most important step is to ensure that the waterjet pierces the material outside of the part outline. After the tool path is created and the machine has been properly set up, the job can be posted to the MAKE software, which is installed on the waterjet's laptop computer, to perform the cut.
# Check the garnet hopper. If it is low, fill it up.
# Check the garnet hopper. If it is low, fill it up.
# Power on the computer and plug in the USB.
# Power on the computer and plug in the USB.
# Power on the water jet cutter.
# Power on the waterjet cutter.
# Open MAKE.
# Open MAKE.
# Zero the water jet cutter head using MAKE.
# Zero the waterjet cutter head using MAKE.
# Push the clear plastic hose into the hole located on the side of the nozzle. This hose is called the abrasive feed tube and is used to mix abrasive into the water.
# Push the clear plastic hose into the hole located on the side of the nozzle. This hose is called the abrasive feed tube and is used to mix abrasive into the water.
# Position the nozzle between two of the metal ribs, close the lid, and test the nozzle using MAKE. When closing the lid, the support bar on the right side of the lid must be lifted otherwise it will not close. There are two things that should be checked when performing the nozzle test. First, check that the water is flowing through the nozzle. This is necessary because the nozzle can get clogged. Second, check that there is abrasive flowing through plastic tube. It flows quickly but can be identified by a sparkling in the tube as it flows.
# Position the nozzle between two of the metal ribs, close the lid, and test the nozzle using MAKE. When closing the lid, the support bar on the right side of the lid must be lifted otherwise it will not close. There are two things that should be checked when performing the nozzle test. First, check that the water is flowing through the nozzle. This is necessary because the nozzle can get clogged. Second, check that there is abrasive flowing through plastic tube. It flows quickly but can be identified by a sparkling in the tube as it flows.
== Safety ==
== Safety ==
The water jet can be a very dangerous machine if not used properly so here are some important safety items to keep in mind. First, Jesus forgives, but 30,000 psi doesn't. So pay attention to these precautions and be safe while operating this machine.
The waterjet can be a very dangerous machine if not used properly so here are some important safety items to keep in mind. First, Jesus forgives, but 30,000 psi doesn't. So pay attention to these precautions and be safe while operating this machine.
# NEVER, EVER, EVER, EVER, EVER turn on the machine without first turning on the water! You could destroy the machine...and your reputation.
# NEVER, EVER, EVER, EVER, EVER turn on the machine without first turning on the water! You could destroy the machine...and your reputation.
# If you see water squirting out the side of the machine while running a cut, don't touch it! It is the fountain of "Bye Bye Fingers."
# If you see water squirting out the side of the machine while running a cut, don't touch it! It is the fountain of "Bye Bye Fingers."
==Certification==
==Certification==
[https://foxtale.georgefox.edu/moodle/enrol/index.php?id=31413 Water Jet FoxTALE Course]
[https://georgefox.instructure.com/courses/1303 Canvas Course]
==Troubleshooting==
==Troubleshooting==