Virtual Reality Welding Station
Model: Augmented Arc Welding Simulator
Ace: Levi Gibson (email@example.com).
Location: The Vault
The virtual reality welder is the industry’s most realistic welding simulation solution for classroom training. For beginner to advanced-level weld students, the AugmentedArc System simulates multiple welding processes, blending real-world and computer-generated images into a unique, augmented reality environment. Below is an example of this piece of equipment being used.
- Base metal - The metal pieces that are being joined together. For the simulator there are several base metal configurations in the form of the blue coupons.
- Coupons - Small pieces of metal used to practice welding.
- Weld Metal/Electrode - The metal added to the base metal to create a weld.
- Torch - The piece that is held while welding and feeds the weld metal into the base metal.
- MIG Welding - Metal inert gas is a welding process in which an electric arc forms between a consumable MIG wire electrode and the base metal, which heats the base metal, causing them to melt and join. Along with the wire electrode, a shielding gas feeds through the welding torch, which shields the process from contaminants in the air. This is the easiest and most common type of welding and it is recommended that you start with this method.
- TIG Welding - Tungsten inert gas is an arc welding process that uses a non-consumable tungsten electrode to produce the weld. The weld area and electrode is protected from oxidation or other atmospheric contamination by an inert shielding gas (argon or helium), and a filler metal is normally used, though some welds, known as autogenous welds, do not require it. This is difficult to master but provides great control when creating a weld. It is also useful for welding many metals besides steel.
- Stick Welding - A manual arc welding process that uses a consumable electrode covered with a flux to lay the weld. An electric current, in the form of either alternating current or direct current from a welding power supply, is used to form an electric arc between the electrode and the metals to be joined. The workpiece and the electrode melts forming a pool of molten metal (weld pool) that cools to form a joint. As the weld is laid, the flux coating of the electrode disintegrates, giving off vapors that serve as a shielding gas and providing a layer of slag, both of which protect the weld area from atmospheric contamination. This is the oldest form of welding and is still popular; however there is not a stick welder in the maker hub.
The operation of the AR Welding station is simple. First you will select a torch for the type of weld you want to practice and plug in the machine. After that it is a simple matter of setting up an exercise based on difficulty, welding method, and weld type. See the image below to learn how to adjust different weld parameters and navigate the software. It is recommended that you start with the pre-programmed exercise to begin and then move on to custom exercises as you become more experienced. The general weld type is determined by what piece is being welded; the options include liner and cylindrical butt, lap, and T joints. Before the exercise begins you will have to calibrate the AR helmet. The calibration process occurs at the beginning of the exercise and is completed by following the instructions given by the AR helmet. After the calibration is completed complete the exercise, view the results, and then repeat.
With the virtual reality welder, students will get the idea as to how the welding machines work, whether that be arc, MIG, or TIG welding. Once students earn a score of 90 or higher on the simulation, they have the opportunity to work with the actual welders in the welding shop.
Setting up Simulator
- Plug in extension cord (make sure it won’t trip anyone) for power.
- Flip switch on back of machine to turn on.
- Press power button on the front of the machine and wait for the system to start up.
- Attach welding process of your choice (see welding processes section down below).
- At login screen, select user. Guest works well.
- Select right or left handed. This is important because it affects the angle the torch should be held at when performing an exercise.
- Open an exercise. There are four choices for creating an exercise: Open, GMAW (MIG), GTAW (TIG), SMAW (Stick). If you know what type of weld you want to practice go for the open exercise because it will allow for the most customization. If this is a new experience, select the type of weld you are practicing and roll with one of the preset courses.
- On the top of the screen the welding parameters are displayed and will be in red if they are not set properly. Use the control panel (pictured below) to adjust them as needed.
- Place Helmet on head and size to head.
- Follow instructions in the helmet to calibrate the simulator to begin welding.
- Press cancel to exit. There is also an option to view results that is very helpful.
Switching Welding Processes
- Take connector of MIG torch and align 4 holes with machine (left side).
- Twist the threaded end, but do not over tighten.
- To remove, unscrew the connector.
- Grab clamp with small cord attached.
- Align pins with the 5 holes of the connector with the receptacle on the machine (right side).
- To remove, press silver button and softly pull straight out (do not twist).
- Grab cable with TIG torch attached.
- Align 4 holes of the connector with the receptacle on the machine (left side - same as MIG).
- Screw in while holding the connector (do not over tighten).
- To remove, unscrew the connector.
- Take helmet off and place on 2nd shelf of cart.
- Disconnect welding process.
- Exit out of the exercise.
- Press power button on front of the machine and wait for screen to be completely blank.
- Flip the switch to off on the back of machine.
- Unplug the extension cord and leave it coiled up neatly underneath the cart.
- Stack work pieces neatly.
- Coil up all cables of torches used and neatly place on the bottom shelf of the cart.
- Don’t drop the helmet, always place on cart when your not wearing it. It is expensive so take good care of it.
- When someone enters the room, make sure they know about the extension cord to prevent tripping.
- Do not aggressively over tighten the connectors of the welding torches or they could be damaged.
- Make sure to press silver button when releasing the connector of the stick torch or it could break.
- Do not cut power to the machine before it is completely shut down.
- Always lay torches completely on top of the table and avoid sharp bends in the wire to prevent damage to the torches.
- Make sure overhead clamp is secured tightly before using or you could get smacked in the head.
- Do not scratch the coupons as the simulator needs the markings to read your weld.
- The most common issue with this device is the AR flickering on and off and this is extremely annoying because the welding process is halted each time this occurs. To fix this pay close attention to the red arrows on the side of the screen and move your view angle around until they disappear signify that the helmet is oriented with the coupon correctly. If the problem persists, press the AR button to perform a lighting calibration.
Besides occasionally updating software, the only required maintenance is general cleaning. General cleaning consists of wiping dust off the machine when needed, making sure the space is kept neat and tidy, and make sure all cords and torches are in their place.
Specific Maintenance Tasks
|Maintenance Procedure||Frequency||Done By|
|General cleaning||After each use or as needed||Student|
|Update Software||Whenever a new version of software is released||ACE|