2,297
edits
Changes
Jump to navigation
Jump to search
Line 10:
Line 10: − + + − + − + + + + + + Line 41:
Line 47: − + − + − Manual [[Media:Manual-508DT.pdf]]+ − + Line 58:
Line 64: − You will need to demonstrate the safe setup and use of the belt/disc sander. You will be sketching an arc onto a piece of scrap material and sanding up to the line using the disc and belt. Make sure to keep the material moving to prevent burning and tearing of the sanding belt/disc.+ Line 83:
Line 89: − + − If belts have hole or tears they need to be replaced.+ − Burnt discs need to be replaced.+ − − The following items need to be periodically lubricated: − * Idler slide (use non hardening grease) − *Table trunnion (use non hardening grease)
→Documentation
|Has imagedesc=
|Has imagedesc=
|Has description=
|Has description=
|Has certification=
|Has certification=https://georgefox.instructure.com/courses/1305
|Has make=Formech
|Has make=Formech
|Has model=508DT
|Has model=508DT
|Has serial number=2728
|Has ace=Nathan Bodenman;nbodenman18@georgefox.edu
|Has ace=Nathan Bodenman;nbodenman18@georgefox.edu
}}
}}
[[{{#show: {{FULLPAGENAME}}|?Has icon|link=none}}|100px|left|top|{{#show: {{FULLPAGENAME}}|?Has icondesc}}]]
[[{{#show: {{FULLPAGENAME}}|?Has icon|link=none}}|140px|left|top|{{#show: {{FULLPAGENAME}}|?Has icondesc}}]]
[[{{#show: {{FULLPAGENAME}}|?Has image|link=none}}|300px|thumb|upright=1.5|{{#show: {{FULLPAGENAME}}|?Has imagedesc}}]]
[[{{#show: {{FULLPAGENAME}}|?Has image|link=none}}|300px|thumb|upright=1.5|{{#show: {{FULLPAGENAME}}|?Has imagedesc}}]]
Make: {{#show: {{PAGENAME}} |?Has make}}
Make: {{#show: {{PAGENAME}} |?Has make}}
Model: {{#show: {{PAGENAME}} |?Has model}}
Model: {{#show: {{PAGENAME}} |?Has model}}
Serial Number: {{#show: {{PAGENAME}} |?Has serial number}}
Ace: {{#show: {{PAGENAME}} |?Has ace.Has name}} ({{#show: {{PAGENAME}} |?Has ace.Has email address}}).
Ace: {{#show: {{PAGENAME}} |?Has ace.Has name}} ({{#show: {{PAGENAME}} |?Has ace.Has email address}}).
Location: {{#show: {{PAGENAME}} |?Is located in facility}}
Location: {{#show: {{PAGENAME}} |?Is located in facility}}
__TOC__
==Description==
==Description==
* '''Table-''' The bed that the mold rests on.
* '''Table-''' The bed that the mold rests on.
* '''Clamp Frame-'''
* '''Clamp Frame-''' The metal bars that captivate the plastic sheet as its heated and stretched over the mold.
* '''Toggle Clamp Screws-'''
* '''Toggle Clamp Screws-'''
*'''Draft-'''
*'''Draft Angle-''' The wall angle of a mold. This helps in removing the plastic off the mold.
Knowing what the different buttons in the touchscreen operation mean is important in operating the vacuum former. The three primary ones are heat , vacuum , and release . For a full list, refer to the manual.
Knowing what the different buttons in the touchscreen operation mean is important in operating the vacuum former. The three primary ones are heat , vacuum , and release . For a full list, refer to the manual.
[[Media:Manual-508DT.pdf|Vacuum Former User Manual]]
==Training==
==Training==
====Overview====
====Operation====
The vacuum former can mold up to a 19"x17" square and to a depth of 7.3".
The vacuum former can mold up to a 19"x17" square and to a depth of 7.3".
====Demonstration====
====Demonstration====
Text here
====Operation====
====Operation====
==Certification==
==Certification==
[https://foxtale.georgefox.edu/moodle/course/view.php?id=31717 Foxtale Course]
[https://georgefox.instructure.com/courses/1305 Canvas Quiz]
==Troubleshooting==
==Troubleshooting==
Make sure to put draft on your form to prevent sticking.
If the plastic is not hot enough it won't pull down over the form.
==Maintenance==
==Maintenance==
====General maintenance====
====General maintenance====
====Specific Maintenance Tasks====
====Specific Maintenance Tasks====