Changes

  |Has model=156F

  |Has model=156F

  |Has serial number=140801D83D63 / 01411-05631 (Air Filter)

  |Has serial number=140801D83D63 / 01411-05631 (Air Filter)

  |Has ace=Zach Cogswell: ZCogswell18@georgefox.edu

  |Has ace=Zach Cogswell;zcogswell18@georgefox.edu

}}

}}

====User Manual====

====User Manual====

*[https://www.itee.uq.edu.au/etsg//filething/get/3156/Speedy-300-Manual-EN.pdf User Guide]

* '''[[Media:JobControl-Manual-EN.pdf|Job Control Operation Manual]]'''

* '''[[Media:8011-speedy300-manual-en.pdf|Speedy 300 Operation Manual]]'''

==Training==

==Training==

*Keep an eye on active cuts because fires can be started when cutting wood or acrylic with paper covering.

*Keep an eye on active cuts because fires can be started when cutting wood or acrylic with paper covering.

*If you feel unsure about anything located in the laser cutting procedure make sure to consult the supervisor for assistance.

*If you feel unsure about anything located in the laser cutting procedure make sure to consult the supervisor for assistance.

==Certification==

==Certification==

====General maintenance====

====General maintenance====

To keep the laser cutter running and cutting smoothly, the mirror and lens should be periodically cleaned. This is on top of the general cleaning that should be done to keep the machine dust and scrap free. There is also filters in the exhaust system that must be changed once the activated carbon has been used up.  

To keep the laser cutter running and cutting smoothly, the mirror and lens should be periodically cleaned. This is on top of the general cleaning that should be done to keep the machine dust and scrap free. There are also filters in the exhaust system that must be changed once the activated carbon has been used up.  

====Specific Maintenance Tasks====

====Specific Maintenance Tasks====

#The lense, mirror, and cone should be inspected daily or more often as needed, especially after wood or other “dusty”/”smokey” materials are cut. The lense will need cleaning when particles are visible on the surface (hold up to light if need be). The lense may be removed using the threaded nut below the lense (see photo). The lense should be cleaned with the lense paper and cleaner available in the kit (lasercutter drawer) on both sides. Put some cleaner on the lense and gently rub the paper over the surface of the lense. The cone itself threads into the assembly below the lense nut. The cone may be cleaned with a paper towel and water or another cleaning agent. The mirror should be inspected and cleaned in the same manner as the lense.

#The lense, mirror, and cone should be inspected daily or more often as needed, especially after wood or other “dusty”/”smokey” materials are cut. The lense will need cleaning when particles are visible on the surface (hold up to light if need be). The lense may be removed using the threaded nut below the lense (see photo). The lense should be cleaned with the lense paper and cleaner available in the kit (lasercutter drawer) on both sides. Put some cleaner on the lense and gently rub the paper over the surface of the lense. The cone itself threads into the assembly below the lense nut. The cone may be cleaned with a paper towel and water or another cleaning agent. The mirror should be inspected and cleaned in the same manner as the lense.

#See above.

#See above.

#The air filter to the right of the Speedy 300 will occasionally need maintenance. The most common issue is a full pre-filter. This will be indicated on the filter itself by poor airflow/suction. When replacing this, use a face mask and gloves (close the lab when doing this). Open the top of the air filter with the large 10mm hex wrench in the kit. Remove the prefilter and place it in a bag for disposal. Insert a new prefilter and close the lid. Pre-filters are used to increase the lifespan of other, harder to replace and more expensive filters in the system. Less often, other filters will need replacing. These include the larger box filter, additional pre-filter-type mat filters, and activated carbon. This should not need to happen as often. Follow the above procedure for pre-filter and the [https://www.youtube.com/watch?v=yJkCgAVbAEU&feature=youtu.be video] to replace the full filter setup. Be careful not to spill activate carbon if doing a full replacement, it is difficult to clean up.

#The air filter to the right of the Speedy 300 will occasionally need maintenance. The most common issue is a full pre-filter (P/N 37722). This will be indicated on the filter itself by poor airflow/suction. When replacing this, use a face mask and gloves (close the lab when doing this). Open the top of the air filter with the large 10mm hex wrench in the kit. Remove the prefilter and place it in a bag for disposal. Insert a new prefilter and close the lid. Pre-filters are used to increase the lifespan of other, harder to replace and more expensive filters in the system. Less often, other filters will need replacing. These include the larger box filter (P/N 41041), additional pre-filter-type mat filters, and activated carbon. This should not need to happen as often. Follow the above procedure for pre-filter and the [https://www.youtube.com/watch?v=yJkCgAVbAEU&feature=youtu.be video] to replace the full filter setup. Be careful not to spill activate carbon if doing a full replacement, it is difficult to clean up.