Getting Started

From maker-hub
Jump to navigation Jump to search
Few Word.png

Reading is hard... but somehow, we need to put the necessary training information into your brain so that you can use the Maker Hub's equipment safely and refrain from breaking things. We'll try to convey all of this in as few words as possible (humor aside). This course should take less than 30 minutes to complete. And we promise, this is the most lengthy course out of all the Maker Hub training courses. For all the "TLDR" peeps in the house, buckle up...


To gain basic card-swipe access to the Maker Hub, read this entire page and pass the Maker Hub Introduction Canvas quiz (with 100%). The link to the Canvas quiz is found toward the bottom of this page here.

How We Operate

The Maker Hub is available to all members of the GFU family (i.e. undergrad students, graduate students, ADP students, and employees), and that includes non-engineering students! The Maker Hub was born to advance creativity, innovation, and entrepreneurship within the community of George Fox University. One of the main ways we achieve this goal is by providing a space where people can work on academic and/or personal projects. The Maker Hub operates under the guidance of a few GFU employees, a handful of student staff, and a plethora of student aces and volunteers. The student staff, aces, and volunteers play critical leadership roles in overseeing various technical shops and training others to use the equipment. With a diverse user-base and a diverse set of projects running concurrently, there has to be a standardized training system that keeps everyone on the same page. And... that's why you're here reading this epic wiki page anyways.

To enable you to access and maintain this space, you are being asked (OK, required) to take a short training course on the Maker Hub. Through this course, you will become acquainted with the facilities within the Maker Hub, the equipment and tools available to you, and the expectations for proper usage of them. The goal of this course is twofold: first, to introduce you to the capabilities available to you in the space, and second, to help you understand the expectations upon you when using the space. Both are crucial if you want to be an active participant in the space.

In any public space, there has to be some set of rules that govern the activity in the space. Ideally, we would just use the clever “Rule 0: Don’t make me make a rule.” But, we felt it was better to come up with some overall guiding principles rather than a list of rules. Clearly, there are some obvious “rules” that get implied from these principles, but, we believe that if you embrace the principles, the rules will take care of themselves. These principles we like to call: The Three Commandments.

(See what we did there? - Christian school - reference to the commandments? Get it?)

The Three Commandments

  1. Safety First
  2. Reset the Space
  3. Be Professional


What Do The Three Commandments Mean?

Safety First
This should be the most obvious--and critical--of the commandments. A significant portion of the equipment and tools in the Maker Hub can be quite dangerous. It is imperative that in everything you do, you address safety first. This starts with general behavior (don’t run with scissors - in fact, don’t run at all - unless there is a fire - and you can see now why we are going with principles rather than specific rules). But beyond general behavior, various rooms and machines have very specific safety procedures and violations of these procedures will come with penalties.

We use the buddy system. It's always a good idea to have a buddy or someone within eyesight or earshot while working anywhere in the Maker Hub. It is IMPERATIVE to have a buddy or someone else present when working in the machine shop, wood shop, or welding lab. Do not use equipment alone in the machine shop, wood shop, or welding lab; it is a serious safety violation.

Safety first includes not only your safety and the safety of others, but the safety of the equipment and tools as well. It is a huge privilege to have access to this set of equipment and we need to ensure that the equipment is being properly used and maintained. There is no reason in this space to use a screwdriver as a hammer. We have hammers. Use tools for their intended purposes, not just for your safety, but for the safety of the tool.

Safety is our number one concern as you use the equipment and tools available in the Maker Hub. In the Maker Hub, there is a very clear distinction between things that are considered equipment and things that are considered tools. Equipment is a special category of machines that, by definition, requires certified training before an individual is allowed to use it. Tools have no certification process; they can be used by anyone who has completed this Maker Hub Introduction course and passed the quiz. That does not mean that tools are necessarily less dangerous; equipment just requires more training. Do not use any equipment that you have not been certified on. There are several equipment stations in The Hub such as the sewing machines, the electronics workstation, and the heat press to name a few. All equipment is marked in the Maker Hub with special icons that are displayed either on, around, or above the equipment. Here's an example icon for the sublimation printer.

Dye Sublimation Printer.png

Equipment that has an icon posted over it, by definition, requires specialized certification training. Without completing this training, you are not authorized to utilize the equipment! Have we beat this dead horse enough yet? Think of these certifications as a “license to learn.” They allow you to utilize the equipment, but you should still feel free to ask for help, at any point, from a shop mentor or technician.

Never forget ... SAFETY FIRST!

Reset the Space
This commandment is simple enough to understand, but sometimes difficult for ... let’s just say it ... people ... to implement. The idea is very simple. Put things back. Leave the space better than you found it. It's not that hard. There is a place for everything, and everything has a place. There are marks on the floor in the Hub for the tables. These are just there to help remind you. This rule applies to EVERYTHING in the space. If you move a chair, put it back. If you move a table, put it back. If you use a tool, put it back. If you use a rolling computer, put it back. That means you don’t take things from one room and leave them in another. You see, that would not be “putting it back.” You see where I am going with this? If you use a machine in the shop, put the tools away. Use the vacuum to clean up. Make the space look better than you found it. If you want a marker for a whiteboard in the space, go request one from the toolroom. They are free for usage in the space. Do not take them from other rooms. Do not take erasers from other rooms. If you use a whiteboard, erase it. I could go on. Sort of want to. But I will contain myself. Ok ... a few more ...

We currently allow food and drink in the Maker Hub. Resetting the Space means that you don’t leave food spills, wrappers, or trays, or anything that wasn’t there when you came in.

Now, we understand that sometimes you need to leave things out. Maybe you are in the middle of a large test and you need something to run overnight. In cases like this, it is OK, but you NEED to leave a note on your system so that others know the situation. This is just common courtesy.

Whatever you do, RESET THE SPACE!

Be Professional
This commandment has two sides to it. It covers the idea of acting like a professional (which Webster’s defines as “exhibiting a courteous, conscientious, and generally businesslike manner in the workplace”). The term also describes the standards of education and training that prepare members of the profession with the particular knowledge and skills necessary to perform their specific role within that profession. Hopefully, you are learning both of these as part of your education at George Fox University. In the Maker Hub we expect you to develop as a courteous, conscientious, and skilled craftsman, understanding the tools and equipment in the Maker Hub and how to use them effectively.

Being a professional has some obvious behavioral ramifications. First, be Christlike. Think of others better than yourselves. Share. If you are using a meeting room to do individual work, and a team needs a meeting room, then you should yield the room. Function is more important than who got there first. This is being a professional.

If you are working with a tool or piece of equipment, and you don’t know the proper way to do what you are attempting - ASK SOMEONE! Learn! Become a professional. Learn the craft. This is an educational space. You might think it will be quick and you can just get it done “your” way and not learn how to do it correctly. Be a Professional and learn the proper way, and then be available to teach others.

One very important, and likely difficult part of being a professional is to correct others when they are not being professional. It is your responsibility to speak up when you see somebody doing something inappropriate. If you see somebody doing something unsafe, not resetting the space, or being unprofessional, the professional thing to do is to remind them of the three commandments and ask them politely to correct their action. This is OUR space, not any individuals. As a group, we expect everyone in the space to keep the space safe, clean, and operable for everyone.

BE PROFESSIONAL!

How We Handle Violations

These are The Three Commandments, and they form the rule and order for the Maker Hub. There are similarities to the rule and order in Christianity. As G.K. Chesterton said in his classic book “Orthodoxy,”

"the more I considered Christianity, the more I found that while it had established a rule and order, the chief aim of that order was to give room for good things to run wild."

It is our hope and expectation that you and other students will be able to run wild and create many wonderful things in this space. These “commandments” are intended to provide that space - and the expectation is that everyone will abide by them. But, as we know, not everyone chooses to do so (1 Tim 1:9-10). We have seen various ways that different schools address these violations, and most use expulsion from the space as the primary penalty. Our penalty system is purposely vague to allow us to handle violations on a case-by-case basis. Some violations (not putting a chair back after moving it) might be comparatively minor, while others are extremely severe. An example of an extremely severe violation would be unauthorized usage of machines in the machine or wood shop, or even authorized use of a machine without anyone else present. These violations would most likely result in immediate suspension from accessing the Maker Hub. Let's just not go there, please.

Ok, moving onward. You might have noticed that the Maker hub is access-controlled; the doors are normally closed, and we are asking you to keep them that way. It is a serious liability concern for the Maker Hub and the university if people are using the space without undergoing the proper safety training. If you're unsure if the people walking behind you have access to the Maker Hub, please don't hold the doors open for them. Or ask... introduce yourself and make new friends. You are certainly welcome to bring friends into certain parts of the space, but you will be held responsible for their behavior. Everyone in the space should understand the three commandments and will be expected to adhere to these principles.

Finally, as a friendly reminder, we have security cameras posted throughout the Maker Hub, so do be on your best behavior. The cameras exist to help protect the space and enforce violations. All public areas are under constant surveillance, and everything is being recorded. This means that, if necessary, the video can be reviewed to help identify nefarious behavior or the cause of an accident. If an accident happens in the Maker Hub, first decide if you need to call an ambulance. Second, notify the Lead Technician and/or Maker Hub Manager. Even if no one got hurt... if you broke something... if something dangerous happened... if a significant malfunction occurred, but then it magically fixed itself later... please notify the Maker Hub employees. It's always better to take initiative in owning your mistakes than for the Maker Hub staff to find out what happened by reviewing the camera footage.

Let's switch gears to a happier topic.

Things You Need To Know About The Hub

Map of the Maker Hub

The Facilities section on the Main Page shows a gallery of the different spaces that comprise the whole Maker Hub. See the map to the right for the layout of the Maker Hub. We will discuss the dark blue areas and the yellow area - which are the hub, meeting rooms, and computer lab.

The Hub
The space we call "The Hub" refers to the large central room, which includes the lobby and hallways (where the Maker Hub logo is on the map). The Hub is a general-use area that is meant for designing and making. It has approximately 8 rolling workbenches, some blue rolling carts, 8 computers on wheels, tool racks on the wall, and some semi-permanent stations.

First, there are approximately 8 open workbenches surrounded by drafting chairs that are open for general use. Each of these has a permanent home that is marked on the floor. Each workbench has power outlets on each leg, which can be powered by plugging the workbench's power plug into the yellow power outlets that come down from the ceiling. The yellow power outlets have been positioned so that that they hang down directly next to the workbench. These workbenches have locking casters and can be moved. However, when you have finished with the workbench, please reset the space. Ensure that the workbench is placed back inside of the special marks on the floor, and place the drafting chairs (usually 4 of them) around the workbench. When you RESET THE SPACE, it makes it nice for those following behind you. And we want to be nice ... don’t we? Yes is the answer to that question. If you need to leave your project out on a workbench for an extended period, you must mark it as "in use" with a note including your name, date, contact info, and when the project will be moved/cleaned up. There should be a good reason for this because we don't want to lock down a workbench for days. If there are special circumstances, please speak with your project advisor and/or a Maker Hub employee.

Project storage is at a premium in the Maker Hub. We do not have a lot of space to store projects. The blue rolling carts that live in the hub are designed for project transportation, not permanent project storage. When you are finished using these carts, please clear them off and return them where you found them. If, for some special reason, you need to use the cart continuously for a short time, mark the cart as "in use" per the description above. This is useful if you want to run overnight tests or you are in the middle of an assembly. However, this is for short term use. Remember, BE PROFESSIONAL. Release the materials for others to use. There are project storage racks in the senior design corridor across. If you want to store your project there, label your shelf/materials with your name, the date, and contact info. Do not swipe labeled materials for your own project. Keep in mind that these storage racks are periodically cleaned out each summer, so please take your projects with you at the end of the spring semester or notify a Maker Hub employee if you want your project to stay over the summer.

There are 8 computers on wheels that live up against the wall facing the quad or between the meeting rooms on the south side of the hub. They are all the same as the Computer Lab machines with the exception of number 8. Computer 8 has the Adobe Creative Suite in addition to all the rest of the software. All of the computers on wheels have a UPS (uninterruptible power supply) that allows you to unplug the machine and move it around the Maker Hub without powering it down. You allegedly have about 15 minutes of power available from the UPS (if anyone actually times it, let us know). Feel free to roll these computers to wherever you want to use them; however, when you are finished, RESET THE SPACE! The computers, when not in use, should always be sitting at their permanent locations plugged into a wall outlet.

On the wall, there are a couple tool racks. These are available for use within the Maker Hub. As should be obvious by now, when you are done using the tools, return them - RESET THE SPACE. Do not take these tools out of the Maker Hub. That's what the Tool Room is for. A tool is to the Tool Room as a book is to the library. Check out tools for an extended period of time and simply return them by the due date. The Tool Room hours are posted on the wiki page.

There is A/V equipment in the corner of the hub. Best to just leave it alone.

The Low-Fidelity Prototyping Station is provided so that students can make quick project mock-ups. Please BE PROFESSIONAL when using this station. While it might be tempting to make pipe-cleaner men as you did in elementary school, these supplies are provided for free to be utilized for projects, not entertainment. We will simply not be able to provide these supplies if they are continually wasted. This station is notorious for being left a mess, so please RESET THE SPACE and clean up when you are finished. Also, there is a small laminating machine located at the low-fidelity prototyping station. The low-fidelity prototyping station and the laminating machine are not considered "equipment," which means that there is no certification process necessary to use these items. See The Hub wiki page to see what equipment is located in the hub.

A neat and orderly Meeting Room :)

Meeting Rooms
There are 8 meeting rooms in the Maker Hub. The intended function of these rooms is to house meetings (i.e. these are not study rooms, but meeting rooms). Which means, priority will be given to weekly meetings with senior design and servant engineering teams and for other team meetings for other classes or projects. When not requested for a team meeting, these rooms can be used by individuals for studying, or by groups for hanging out. If you are acting like a professional, then you will yield the room to others who have a legitimate project-related need for the meeting room. That is, if you are watching a video by yourself, or studying by yourself or in a group, and the other rooms are full, and a team needs to meet, it would be very professional to offer them the room and then study elsewhere. Likewise, if a team would like to use a room at an unscheduled time, it would be professional to look for an empty room first, and then a room that has the least effect on others who might be using the room for group study or other activities.

Each of these rooms is equipped with a wall-mounted monitor and HDMI connection. There is a whiteboard in each room as well. As with other whiteboards, please do not take the erasers or markers, and always erase when you have finished using the whiteboard. If there are no markers or erasers, please obtain them from the toolroom. When you leave the room, turn off the TV, and make sure that the HDMI cable is accessible.

Each of these rooms should have a table (haven’t seen anyone take those yet) and seven chairs without arms. There are seven as many senior design teams have two faculty mentors and five students. There should not be any stools in these rooms. By stools, we mean the higher chairs that are out in the Hub. Stools should stay at the tables in the Hub. If you need more chairs, or for some reason want less chairs, they are movable. Just remember that you should always RESET THE SPACE.

We have added some coat hangers on the wall behind the door. These are only for coats, they will not be strong enough to hold backpacks.

When you leave a meeting room, there should be a TV on the wall and an HDMI cable. There should be 1 table, 7 chairs, 0 stools, 0 rolling computers, and a clean whiteboard with an eraser and markers.

Enjoy the meeting rooms - just remember the three commandments.

Computer Lab
The computer lab consists of 29 computers (designed as 28 for students and 1 for instructors). Each of these stations consists of the computer, the keyboard, the mouse, and a chair with arms. These are a unit. Which should make it clear that you should never take a keyboard, a mouse, or a chair from this space. There are no chairs with arms in the Maker Hub or meeting rooms. So, leave the arm chairs in the computer lab. The keyboards and mice are intended for these computers. If you need a keyboard or a computer for your machine, or if one is broken somewhere, inform the toolroom. If there is a dire situation where you need to make use of one of these systems, as always, RESET THE SPACE. It is not acceptable for your peers to arrive in a class the following morning with computers that are missing mice or chairs.

There are large whiteboards in the computer lab that are very useful for ... er ... marking on. And here are some good rules for whiteboards - again - RESET THE SPACE. This means that you don’t take markers or erasers from other whiteboards because the ones at your space are missing or not functional. Go to the toolroom and get new ones. They are freely supplied. If the toolroom is closed, maybe you can use your own makers. Whatever you do, RESET THE SPACE. And when you have finished using a whiteboard .. ERASE IT. This is not only resetting the space, but being a professional. Others will want to use it and you are making them clean up your mess. As a side note, this is a public space. If you want to save your whiteboard writing, take a picture. Writing “Do Not Erase” is not an acceptable action for a whiteboard. You can save it yourself and reproduce it quickly later. Again, BE PROFESSIONAL.

While cleaning up after yourself is a general rule, it is particularly important in the computer lab as folks are very likely to spend a considerable amount of time in there. This means you need to be sure to clean up any papers, food, and drink. If you are in a class or lab and receive a handout, it is your job to study it like your wonderful professor intended. But if you are not going to do that, it is your responsibility to throw it away. Leave the space better than you found it.

There is a set of 72 small lockers in this room. Their main function is to hold materials for classes and labs for students in those classes and labs. If they are not all in use (and they generally aren’t), they can also be used to house small projects. They are not to be used as personal lockers for non Maker Hub related items. Now clearly, If you are using a locker for Maker Hub reasons, then it is certainly fine to place a textbook or engagement ring in there (preferably in the spring). But don’t secure a locker if you are not actively working on a project or participating in a class/lab. To use the lockers, you will need your own lock. At the end of each semester, the lockers should be cleared out and the locks removed. If there are still locks on them, this will give us a chance to use the bolt cutters and sell the contents on the web. That is always a good time. If you need to maintain a locker over the break, you will need to coordinate with the technician. Please do not set things on top of the lockers. These items will be routinely disposed of without warning. Clearly, setting something on top would not be resetting the space, and hopefully you are discovering that this is an important commandment.

How The Training System Works

Anyone need a snack break? to stand up and stretch? a brief intermission? Almost there!

Each of the shops/labs below has controlled access. To acquire access to these labs, there will be a training course for each room in addition to the specific machine training courses. Those courses will cover the more specific application of the three commandments as well as the specific capabilities in each room.

The training will be offered via a Canvas course for each piece of equipment. If the system is relatively simple, the course might just be basic reading with a simple quiz (like this one). More complex tools might involve demonstration videos along with a live demonstration of your ability to properly use the machines.

How does our training system work? Take a look at the fancy graph below. Every node on the graph has a corresponding Canvas quiz (unless it is labelled with (No Quiz)). The middle column contains all of the facilities within the Maker Hub; most facilities have a corresponding Canvas Quiz. The right column contains each piece of equipment within the Maker Hub... and you guessed it; each piece of equipment has its respective quiz. The graph follows a sequential process of completing quizzes from left to right. For example, if I wanted to get certified on the Milling Machine, I would need to take the Maker Hub Intro quiz, then the Machine Shop quiz, then the Milling Machine quiz. All of the information I would need to pass these 3 quizzes can be found at the respective links given. After that, let's say that I also wanted to get certified on the Sewing Machine. Well, I've already passed the Maker Hub Intro quiz, and there's no quiz for The Hub... so I only need to pass the Sewing Machine quiz. So on and so forth. Keep in mind that all Canvas quizzes are reset at the beginning of the summer, so you will need to retake all your quizzes in the fall (but all demonstrations carry over). This is intentional to refresh your knowledge of how to operate each machine once a year.

Certification

Maker Hub Introduction Canvas Quiz

What's Next?

After you have passed the Maker Hub Introduction quiz on Canvas with 100%, you should receive card-swipe access to the main doors of the Maker Hub on the following day (because the card reader system updates at midnight).