Line 10: |
Line 10: |
| |Has imagedesc=Protoflow Reflow Oven | | |Has imagedesc=Protoflow Reflow Oven |
| |Has description= | | |Has description= |
− | |Has certification= | + | |Has certification=https://georgefox.instructure.com/courses/1281 |
| |Has make=Miller | | |Has make=Miller |
| |Has model=LMSW-52 | | |Has model=LMSW-52 |
| + | |Has serial number=MJ328801N |
| |Has group=Circuit Board Design | | |Has group=Circuit Board Design |
− | |Has ace=Chandler Wann;cwann18@georgefox.edu | + | |Has ace=Levi Gibson;lgibson19@georgefox.edu |
| }} | | }} |
− | [[{{#show: {{FULLPAGENAME}}|?Has icon|link=none}}|100px|left|top|{{#show: {{FULLPAGENAME}}|?Has icondesc}}]] | + | [[{{#show: {{FULLPAGENAME}}|?Has icon|link=none}}|140px|left|top|{{#show: {{FULLPAGENAME}}|?Has icondesc}}]] |
| | | |
| Make: {{#show: {{PAGENAME}} |?Has make}} | | Make: {{#show: {{PAGENAME}} |?Has make}} |
| | | |
| Model: {{#show: {{PAGENAME}} |?Has model}} | | Model: {{#show: {{PAGENAME}} |?Has model}} |
| + | |
| + | Serial Number: {{#show: {{PAGENAME}} |?Has serial number}} |
| | | |
| Ace: {{#show: {{PAGENAME}} |?Has ace.Has name}} ({{#show: {{PAGENAME}} |?Has ace.Has email address}}). | | Ace: {{#show: {{PAGENAME}} |?Has ace.Has name}} ({{#show: {{PAGENAME}} |?Has ace.Has email address}}). |
| | | |
| Location: {{#show: {{PAGENAME}} |?Is located in facility}} | | Location: {{#show: {{PAGENAME}} |?Is located in facility}} |
| + | |
| | | |
| __TOC__ | | __TOC__ |
| + | |
| + | ==Safety First== |
| + | [[File:Safety First HD2.png|left|150px]] |
| + | * Wear gloves and welding helmet. |
| + | * Don't have bare skin exposed. |
| + | * Don't weld in wet gear or standing water. |
| + | * Welded material will be hot. |
| + | |
| + | |
| + | |
| | | |
| ==Description== | | ==Description== |
Line 38: |
Line 52: |
| ==Documentation== | | ==Documentation== |
| | | |
− | * [https://www.millerwelds.com/files/owners-manuals/O359H_MIL.pdf Owner's Manual]
| + | [[Media:Spot_Welder_Manual.pdf|Spot Welder User Manual]] |
| + | |
| ====Terminology==== | | ====Terminology==== |
| | | |
Line 57: |
Line 72: |
| # Turn on the spot welder | | # Turn on the spot welder |
| # Place the material being welded between the clamps. | | # Place the material being welded between the clamps. |
− | # Clamp down on the two pieces of material for no more than 5 seconds. | + | # Clamp down on the two pieces of material for approximately 2 seconds. The time required to weld may vary slightly depending on the material and thickness. |
| # Grab workpiece with a set of pliers, and open the clamp. | | # Grab workpiece with a set of pliers, and open the clamp. |
| <references /> | | <references /> |
− |
| |
− | ==Safety==
| |
− | # Wear gloves and welding helmet.
| |
− | # Don't have bare skin exposed.
| |
− | # Don't weld in wet gear or standing water.
| |
− | # Welded material will be hot.
| |
| | | |
| ==Certification== | | ==Certification== |
| | | |
− | [https://foxtale.georgefox.edu/moodle/mod/quiz/view.php?id=812600 Foxtale Course] | + | [https://georgefox.instructure.com/courses/1281 Canvas Quiz] |
| | | |
| ==Troubleshooting== | | ==Troubleshooting== |
Line 84: |
Line 93: |
| !Done By | | !Done By |
| |- | | |- |
− | |Check Argon Pressure | + | |xxx |
− | |Before Use | + | |xxx |
| |Student/Tech | | |Student/Tech |
| |- | | |- |
− | |Check Coolant Flow | + | |xxxx |
− | |Before Use | + | |xxxx |
| |Student/Tech | | |Student/Tech |
| |- | | |- |
− | |Inspect collet & Cup | + | |xxxx |
− | |Before Use | + | |xxxx |
| |Student/Tech | | |Student/Tech |
| |} | | |} |