Difference between revisions of "Drill Press"
| Line 44: | Line 44: | ||
==Training== | ==Training== | ||
====Overview==== | ====Overview==== | ||
| − | Begin by clamping your piece down with the vice. The exact positioning of the piece is not critical because it can be changed later with the x-y adjustments. Do not try to drill without the piece being clamped or it may catch and turn into a spinning blade. It is also possible to twist and raise the work table if needed. Insert the desired drill bit into the chuck and tighten it with the chuck key. Make sure the bit is in centered in the chuck and that there is at least a 1/8" gap between the bottom of the chuck and the end of the drill's grooves. Note that you should start the hole with the hole starter tool before using the actual bit. Fine tune the position of the piece using the x-y adjustments and turn on the drill press with the start button. Adjust the speed to match the material you are drilling. You can find the correct speed on the chart above the mills. Also, ONLY adjust the speed while the drill press is ON to prevent damage to the drill press. Now you can drill your hole. For optimal results, lubricate the cutting area with machining oil before drilling a use peck drilling, i.e. drilling down a small amount, lifting out the bit to clear scraps from the hole, and then repeating. | + | Begin by clamping your piece down with the vice. The exact positioning of the piece is not critical because it can be changed later with the x-y adjustments. Do not try to drill without the piece being clamped or it may catch and turn into a spinning blade. It is also possible to twist and raise the work table if needed. Insert the desired drill bit into the chuck and tighten it with the chuck key. Make sure the bit is in centered in the chuck and that there is at least a 1/8" gap between the bottom of the chuck and the end of the drill's grooves. Note that you should start the hole with the hole starter tool before using the actual bit. Fine tune the position of the piece using the x-y adjustments and turn on the drill press with the start button. Adjust the speed to match the material you are drilling. You can find the correct speed on the chart above the mills. Also, ONLY adjust the speed while the drill press is ON to prevent damage to the drill press. Now you can drill your hole. For optimal results, lubricate the cutting area with machining oil before drilling a use peck drilling, i.e. drilling down a small amount, lifting out the bit to clear scraps from the hole, and then repeating. Don't forget to reset the space by cleaning up any metal chips and returning any drill bits that were used during the process. |
====Demonstration==== | ====Demonstration==== | ||
| − | + | The demonstration for the drill press is simple. All you need to do is perform the correct drilling procedure while drilling a hole in a piece of scrap metal. | |
====General Procedure==== | ====General Procedure==== | ||
This video contains specific information for using the drill press in the Maker Hub as well as a basic overview of what will be expected in your live demonstration.{{#evu:https://www.youtube.com/watch?v=MJWyROfHOd8}} | This video contains specific information for using the drill press in the Maker Hub as well as a basic overview of what will be expected in your live demonstration.{{#evu:https://www.youtube.com/watch?v=MJWyROfHOd8}} | ||
==Safety== | ==Safety== | ||
| − | + | * Wear proper safety equipment like safety glasses and closed toed shoes because metal chips can hurt. | |
| + | |||
| + | * Keep hands clear of moving tools/blades. This should be pretty obvious. | ||
| + | |||
| + | * Don't run machine in reverse as it can harm the drill bits. | ||
| + | |||
| + | * Make sure material is secure in the vice. If it comes loose the material will become a spinning blade. | ||
| + | |||
| + | * No hats, jewelry, watches, hair below the shoulders, baggy long sleeves, or gloves while operating the drill press. These can all get caught in the drill bit and cause significant harm. | ||
| + | * Don't brush away shavings while the machine is running. This is a common temptation but can end in getting caught in the drill bit. | ||
==Certification== | ==Certification== | ||
| Line 60: | Line 69: | ||
==Troubleshooting== | ==Troubleshooting== | ||
| + | * Difficulty Cutting - Add machining oil and re | ||
==Maintenance== | ==Maintenance== | ||
====General maintenance==== | ====General maintenance==== | ||
| − | + | The only things that need to be done to maintain the drill press are general cleaning and periodic lubrication of key joints. For details on the lubrication process see the user manual. | |
====Specific Maintenance Tasks==== | ====Specific Maintenance Tasks==== | ||
| Line 71: | Line 81: | ||
!Frequency | !Frequency | ||
!Done By | !Done By | ||
| + | !Last Completed | ||
| + | |- | ||
| + | |Clean up metal shavings | ||
| + | |After each use | ||
| + | |Student | ||
| + | |N/A | ||
|- | |- | ||
| − | | | + | |Lubricate key components |
| − | | | + | |As needed |
| − | | | + | |Ace |
| + | | | ||
|} | |} | ||
Revision as of 12:29, 17 July 2019
Make: Clausing
Model: 20" Variable Speed
Ace: Needed (Makerhub@georgefox.edu).
Location: Machine Shop
Description
The Clausing Drill Press is a 20” variable speed drill press primarily used for drilling holes when absolute precision is not a requirement. Often this machine is helpful when a noncritical hole is needed on a part because it is possible to drill perpendicular holes in parts somewhat accurately, but not with the precision of a mill.
Documentation
Terminology
- Spindle - The rotating shaft that transfers power the drill bit.
- Quill - The tube surrounding the spindle which moves up and down when drilling a hole but does not rotate.
- Chuck - The clamping device that holds the drill bit and is attached to the end of the spindle.
- Vice - The device that securely holds the work piece.
User Manual
Training
Overview
Begin by clamping your piece down with the vice. The exact positioning of the piece is not critical because it can be changed later with the x-y adjustments. Do not try to drill without the piece being clamped or it may catch and turn into a spinning blade. It is also possible to twist and raise the work table if needed. Insert the desired drill bit into the chuck and tighten it with the chuck key. Make sure the bit is in centered in the chuck and that there is at least a 1/8" gap between the bottom of the chuck and the end of the drill's grooves. Note that you should start the hole with the hole starter tool before using the actual bit. Fine tune the position of the piece using the x-y adjustments and turn on the drill press with the start button. Adjust the speed to match the material you are drilling. You can find the correct speed on the chart above the mills. Also, ONLY adjust the speed while the drill press is ON to prevent damage to the drill press. Now you can drill your hole. For optimal results, lubricate the cutting area with machining oil before drilling a use peck drilling, i.e. drilling down a small amount, lifting out the bit to clear scraps from the hole, and then repeating. Don't forget to reset the space by cleaning up any metal chips and returning any drill bits that were used during the process.
Demonstration
The demonstration for the drill press is simple. All you need to do is perform the correct drilling procedure while drilling a hole in a piece of scrap metal.
General Procedure
This video contains specific information for using the drill press in the Maker Hub as well as a basic overview of what will be expected in your live demonstration.
Safety
- Wear proper safety equipment like safety glasses and closed toed shoes because metal chips can hurt.
- Keep hands clear of moving tools/blades. This should be pretty obvious.
- Don't run machine in reverse as it can harm the drill bits.
- Make sure material is secure in the vice. If it comes loose the material will become a spinning blade.
- No hats, jewelry, watches, hair below the shoulders, baggy long sleeves, or gloves while operating the drill press. These can all get caught in the drill bit and cause significant harm.
- Don't brush away shavings while the machine is running. This is a common temptation but can end in getting caught in the drill bit.
Certification
Foxtale Quiz
Troubleshooting
- Difficulty Cutting - Add machining oil and re
Maintenance
General maintenance
The only things that need to be done to maintain the drill press are general cleaning and periodic lubrication of key joints. For details on the lubrication process see the user manual.
Specific Maintenance Tasks
| Maintenance Procedure | Frequency | Done By | Last Completed |
|---|---|---|---|
| Clean up metal shavings | After each use | Student | N/A |
| Lubricate key components | As needed | Ace |