Belt/Disc Sander

Belt and Disc Sander

Make: PowerMatic

Model: BD31A

Serial Number: 18100721

Ace: Needed (Makerhub@georgefox.edu).

Location: Wood Shop

Safety First

• Sanding creates heat due to the friction. Keep material moving to prevent damage to the sanding belt/disc.
• Never position your hand so that it would make contact with the belt or disc if it slipped.
• Never reach over the machine while working or turning off the power. This can be very dangerous as you or your clothing could be drawn into the spinning belt or disc.
• Use a brush when clearing sawdust from the table, not your hands.
• Use light pressure when removing material while shaping your piece. Never try to force feed the machine.
• Avoid kickbacks by sanding on the correct side of the disc. Always sand on the downward side of the disc, which is just left of center on a disc rotating counterclockwise. Sanding on the wrong side is dangerous and can pull your work out of your hands.

Description

The disc sander allows you to quickly remove material on outside corners and flat surfaces. The belt sander allows you to remove material on large inside corners and flat surfaces.

Here is an example of this piece of equipment being used.

Documentation

Terminology

Belt/Disc Sander User Manual

Training

Operation

The disc sander allows you to sand outside corners and flat surfaces using an abrasive disc. The belt can perform inside corner and flat surface sanding. The table angles can be adjusted to change the angle of cuts. The sanding table can be set between 15 degrees up and 45 degrees down. The belt arm can be adjusted to 0, 45 and 90 degrees with the arm locking handle. It is important to inspect the sanding disc and belt for wear before use. If you notice any holes or cuts in a belt let the supervisor know before trying to power the machine. Tears can be caused by leaving material in the same spot too long. Try to keep work moving across the belt/disc to prevent damage. The disc normally won't tear but it will turn dark and have burn marks.

Demonstration

You will need to demonstrate the safe setup and use of the belt/disc sander. You will be sketching an arc onto a piece of scrap material and sanding up to the line using the disc and belt. Make sure to keep the material moving to prevent burning and tearing of the sanding belt/disc. To save yourself some time now and in the future, it might be good to pick up an endorsement for the vertical wood bandsaw. If you do so, then you can use the bandsaw to rough cut your arc before taking it to the sander.

General Procedure

1. Obtain a piece of scrap wood. If the work piece is too small it will be difficult to hold onto and create a dangerous situation by placing your fingers too close to the belt/disc.

2. Using a pencil or pen sketch a radius or line onto the edge of your material.

3. Make sure the belt and disc are in good shape and secure.

4. Connect the dust collector hose to the sander.

5. Power on the dust collector and sander.

6. Place the material onto the table and slowly feed your material into the belt/disc using both hands for a rigid grip. Make sure your hands/fingers are clear of any moving parts.

7. Keep the material moving to prevent too much heat in one spot.

8. Keep sanding until you cut the material back to your line.

9. When you are finished sanding power down the dust collector and sander.

10. Make sure all motion has stopped before cleaning the machine.

11. Reset the space.

Certification

Complete the Wood Shop - Belt/Disc Sander Module at the link below to gain access to the Belt/Disc Sander. The Maker Hub Canvas course pertains to all facilities and equipment contained in the Maker Hub; simply complete the quizzes for the facilities/equipment you wish to use in the Maker Hub. Please email makerhub@georgefox.edu if you have any questions.

Maker Hub Canvas Course

Troubleshooting

If belts have hole or tears they need to be replaced. Burnt discs need to be replaced.

Maintenance

General maintenance

The following items need to be periodically lubricated:

• Idler slide (use non hardening grease)
• Table trunnion (use non hardening grease)

Specific Maintenance Tasks

Maintenance Procedure	Frequency	Done By
Replace sanding Belt/Pad	As Needed	Ace/Tech