1,953
edits
Changes
Jump to navigation
Jump to search
Line 116:
Line 116: + + + + + + + + + + + + + + + + + + + + + + + + + + +
→Troubleshooting
==Troubleshooting==
==Troubleshooting==
'''First of all, check your export settings'''
* There are multiple combinations of settings that will work for export; which means that depending on who was using the machine last, settings may be different. These are the settings I (the ace) have found to work most consistantly: Set your Inkscape document to square by going to File > Document Properties (or press Ctl+Shift+D) and set both the Height and Width fields to the same value, bigger than your shape. Why this is an issue is yet unknown, Inkscape just doesn’t like exporting non-square documents with the other settings to follow. Print the document with File > Print or Ctl+P. Click preferences and check both “Take From Application” and “Minimize to Jobsize.” These settings tell the program to assume the canvas is the same size as Inkscape and then crop to the size of your print. Also verify “image mode” is set to “color.” These settings will fix most common issues.
'''Cuts are not being made'''
* Some export settings may be incorrect. Verify that your settings are set to those described above. These settings will fix most issues of lines not cutting.
* Verify that all stokes are set to red with a stroke width between 1pt and .25pt (.25pt recommended)
* Verify that your print is entirely within the canvas of Inkscape.
* In Preferences, within Print options, verify “image mode” is set to “color.” Otherwise, your red stokes will not be read as color, and not be seen by the laser cutter.
'''The cuts did not go all the way through the material'''
* Are you using the correct material profile? If not, rest the job (described below) and repeat the cut with the correct material profile. If it appears that the cut went partway through the material you may want to use a setting that is less powerful than your material would normally use (again, described below)
* You should always place your material in a corner. This way, if the cuts do not go all the way through you can reposition it easily. DO NOT MOVE THE JOB in JobControl! If you put the material in a corner, should be able to place the material back where it was, and then reset the job in JobControl by right clicking on the job in JobControl and selecting the reset job option, or by pressing Ctl+R. Next, run the cut again on the smallest thickness setting for your material. For example, if you are cutting 1/4 inch acrylic and it does not cut all the way through, repeat the cut with the 1/8 inch acrylic setting.
* If you are using the correct material profile for your material and cuts are not going all the way through, please email me and let me know so that I can take a look and fix the settings. ZCogswell18@georgefox.edu
'''The laser went really fast leaving a sort of light engrave rather than a cut'''
* You did not select the correct material, and the job ran with the ‘standard’ setting. DO NOT MOVE THE MATERIAL! You can reset the job by right clicking on the job in Job Control and selecting the reset job option, or by pressing Ctl+R. Then, select the correct material in the upper left dropdown menu and run the job again. This way you do not need to reposition the material or job, which you will almost never do perfectly.
'''The laser repeated the cut multiple times'''
* Some material profiles, such as half-inch, acrylic are set to repeat the cut line multiple times, as to get a cleaner product. If the cuts look good, this is normal.
* Are you importing from SolidWorks? For some reason, SolidWorks likes to have duplicate lines quite often. In Inkscape, click on the cut that was repeated and drag to move it. If you move the line and another line is underneath, you need to delete all duplicates in the file. Often if you have a thin stoke (.25pt) and zoom out, the duplicate lines will be visually darker, allowing you to identify and delete them.
'''The acrylic is melted or blackened'''
* Verify that you are using the correct material profile. If you are, for example, cutting 1/4 acrylic with the 1/2 setting, the acrylic will be melted and not give clean cuts.
* Are you importing from SolidWorks? As mentioned above, “''For some reason, SolidWorks likes to have duplicate lines quite often. In Inkscape, click on the cut that was repeated and drag to move it. If you move the line and another line is underneath, you need to delete all duplicates in the file. Often if you have a thin stoke (.25pt) and zoom out, the duplicate lines will be visually darker, allowing you to identify and delete them.”''
'''Cuts are not clean'''
* Is the machine focused properly for your material? If you’re not sure, or even if you are (you may have bumped the bed control buttons accidentally) refocus it.
* Check the lens for dust because this can interfere with the laser. If it is dirty, see the maintenance section on how to clean it.
'''The material is being cut in unintended places'''
* Check your Inkscape file and make sure there are no red stokes in places you did not want
* Make sure there are no other jobs on the work area (grey rectangles in the honeycomb area of JobControl). If there are, drag them back into the list on the right side or delete them
*
==Maintenance==
==Maintenance==