148
edits
Changes
Jump to navigation
Jump to search
Line 13:
Line 13: − [[{{#show:{{FULLPAGENAME}}|?Has icon|link=none}}|100px|left|top|{{#show: {{FULLPAGENAME}}|?Has icondesc}}]] Line 21:
Line 20: + Line 116:
Line 116: + + + Line 134:
Line 137: − + Line 141:
Line 144: − + Line 149:
Line 152: − + Line 156:
Line 159: − + Line 164:
Line 167: − + Line 171:
Line 174: − +
no edit summary
[[{{#show: {{FULLPAGENAME}}|?Has image|link=none}}|375px|thumb|upright=1.5|{{#show: {{FULLPAGENAME}}|?Has imagedesc}}]]
[[{{#show: {{FULLPAGENAME}}|?Has image|link=none}}|375px|thumb|upright=1.5|{{#show: {{FULLPAGENAME}}|?Has imagedesc}}]]
In this [[TV]], we will take you through the steps of drawing a Triangle in [[Solidworks|SolidWorks]] and fabricating it using the [[Hand Bender]].
In this [[TV]], we will take you through the steps of drawing a Triangle in [[Solidworks|SolidWorks]] and fabricating it using the [[Hand Bender]].
<br>
<br>
<br>
<br>
__TOC__
<br>
<br>
<br>
<br>
==Hand Bender==
==Hand Bender==
<br>
<strong>Step 1:</strong>
Using a piece of metal rod and the hand bender, you will make your triangle. This TV uses ¼” brass stock.
Using a piece of metal rod and the hand bender, you will make your triangle. This TV uses ¼” brass stock.
<br>
<br>
<strong>Step 2:</strong>
The point of the bend is found using smart dimension again. Select the bottom line of the triangle to apply the dimension; again, leave the dimension driven.
The point of the bend is found using smart dimension again. Select the bottom line of the triangle to apply the dimension; again, leave the dimension driven.
<br>
<br>
<br>
<br>
<strong>Step 3:</strong>
From that mark, measure 26.5 mm (~1in) and make another mark. This is the perimeter of the rounded corner. We will find this by using the “Measure” tool under the evaluate tab. Select the curve you want to measure, and the information will appear in the measure pop up box. Measure will give you a lot of information, but here we are just interested in the arc length.
From that mark, measure 26.5 mm (~1in) and make another mark. This is the perimeter of the rounded corner. We will find this by using the “Measure” tool under the evaluate tab. Select the curve you want to measure, and the information will appear in the measure pop up box. Measure will give you a lot of information, but here we are just interested in the arc length.
<br>
<br>
<br>
<br>
<strong>Step 4:</strong>
Repeat the same markings from the other end of the rod.
Repeat the same markings from the other end of the rod.
<br>
<br>
<br>
<br>
<strong>Step 5:</strong>
Moving on to the hand bender. The hand bender has two pins: the radius pin in the center that sets the radius of the bend, and the holding pin that holds the piece of metal against the radius pin.
Moving on to the hand bender. The hand bender has two pins: the radius pin in the center that sets the radius of the bend, and the holding pin that holds the piece of metal against the radius pin.
You are going to position the rod so the first mark from the end is held between the radius and the holding pin. Make sure that the rod is held tightly between the pins.
You are going to position the rod so the first mark from the end is held between the radius and the holding pin. Make sure that the rod is held tightly between the pins.
<br>
<br>
<strong>Step 6:</strong>
Pull the handle to bend the rod until the second mark touches the center pin. Then bend it a bit further because the metal has some spring so it will bounce back slightly.
Pull the handle to bend the rod until the second mark touches the center pin. Then bend it a bit further because the metal has some spring so it will bounce back slightly.
<br>
<br>
<br>
<br>
<strong>Step 7:</strong>
Repeat this using the marks on the other side. Tie a string to the top, and now you have a triangle! Call the family to dinner or go make some music!
Repeat this using the marks on the other side. Tie a string to the top, and now you have a triangle! Call the family to dinner or go make some music!
<br>
<br>
[[File:Triangle complete.png|750px|none]]
[[File:Triangle complete.png|750px|none]]