Changes

  |Is used in domain=Electronics

  |Is used in domain=Electronics

  |Has name={{PAGENAME}}

  |Has name={{PAGENAME}}

  |Has icon=File:Speedy400_Laser.png

  |Has icon=File:Speedy400_Laser.png

  |Has icondesc=Laser Engraver Icon

  |Has icondesc=Laser Engraver Icon

  |Has description=

  |Has description=

  |Has certification=https://georgefox.instructure.com/courses/1212

  |Has certification=https://georgefox.instructure.com/courses/1212

  |Has make=Trotec

  |Has view license key=0009999KWTSZCF9F

  |Has model=Speedy 400

  |Has activation license key=00099992K2C69A5B

  |Has ace= Emily Hayes;ehayes19@georgefox.edu

  |Has ace= Zach Cogswell;zcogswell18@GeorgeFox.edu

}}

}}

[[{{#show: {{FULLPAGENAME}}|?Has icon|link=none}}|140px|left|top|{{#show: {{FULLPAGENAME}}|?Has icondesc}}]]

[[{{#show: {{FULLPAGENAME}}|?Has icon|link=none}}|140px|left|top|{{#show: {{FULLPAGENAME}}|?Has icondesc}}]]

==Documentation==

==Documentation==

The Speedy 400 uses the same software and general setup as the Speedy 300, however it has a larger bed and a few backend setting differences. Should be able to train on either the 300 or 400 and use both machines.  

The Speedy 400 uses the same software and general setup as the Speedy 300, however it has a larger bed and a few backend setting differences. Should be able to train on either the 300 or 400 and use both machines.  

 

NOTE: Currently, the Speedy 400 should not be used for acrylic**. There are some issues with settings/airflow that cause acrylic to often catch fire while cutting (which, as you would imagine, is bad)

NOTE: Currently, the Speedy 400 should not be used for acrylic**. There are some issues with settings/airflow that cause acrylic to often catch fire while cutting (which, as you would imagine, is bad)

** If you know what you are doing and are very careful, small (<10 inches) pieces of 1/4" or 1/8" acrylic allow for sufficient airflow to avoid catching fire. Small pieces of 1/2" acrylic can often work as well, as long as you are careful. If the fumes light fire while cutting, pause the print IMMEDIATELY (the same button as start), or, if needed, stop it entirely (although this will abort the cut and you will not be able to continue). Often pausing allows the fire to go out and the acrylic to cool down, so for small cuts you may be able to continue, carefully, after pausing. If you must cut large sheets of acrylic, remove the paper from the area you are cutting, as close to the size of your cut as possible. Although it is not the paper that is burning, removing it seems to reduce the possibility of fire. Try not to remove any more paper than absolutely necessary, as the paper keeps the acrylic clean and protected from scratches when in the stock pile.

** If you know what you are doing and are very careful, small (<10 inches) pieces of 1/4" or 1/8" acrylic allow for sufficient airflow to avoid catching fire. Small pieces of 1/2" acrylic can often work as well, as long as you are careful. If the fumes light fire while cutting, pause the print IMMEDIATELY (the same button as start), or, if needed, stop it entirely (although this will abort the cut and you will not be able to continue). Often pausing allows the fire to go out and the acrylic to cool down, so for small cuts you may be able to continue, carefully, after pausing. If you must cut large sheets of acrylic, remove the paper from the area you are cutting, as close to the size of your cut as possible. Although it is not the paper that is burning, removing it seems to reduce the possibility of fire. Try not to remove any more paper than absolutely necessary, as the paper keeps the acrylic clean and protected from scratches when in the stock pile.

====Terminology====

====Terminology====

* Honeycomb Table - This is the honeycomb shaped metal tray that holds flat material during a cut. It is used for most cut jobs.   

* Honeycomb Table - This is the honeycomb shaped metal tray that holds flat material during a cut. It is used for most cut jobs.   

* Rotary Tool - When engraving water bottles or glasses, this accessory is used to hold the object in place as well as rotate it while performing a cut.

* Rotary Tool - When engraving water bottles or glasses, this accessory is used to hold the object in place as well as rotate it while performing a cut.

====Manuals====

====Manuals====

* '''[[Media:JobControl-Manual-EN.pdf|Job Control Operation Manual]]'''

* '''[[Media:JobControl-Manual-EN.pdf|Job Control Operation Manual]]'''

* '''[[Media:Speedy-400-Manual-EN.pdf|Speedy 400 Operation Manual]]'''

* '''[[Media:Speedy-400-Manual-EN.pdf|Speedy 400 Operation Manual]]'''