1,947
edits
Changes
Jump to navigation
Jump to search
Line 10:
Line 10: − + − + − + Line 28:
Line 28: + Line 37:
Line 38: + + − * [https://www.janome.com/siteassets/support/manuals/sergers/inst-book-634d.pdf User Manual] − − − + − + − * Push stick - A piece of wood or plastic used to push the wood being cut through the blade while keeping fingers away from the blade. − * Fence - A guide for measuring the cut and guiding the wood. − * Riving Knife - A flat metal device that mounts behind the saw blade. This device prevents material from closing up on the blade and causing a dangerous condition called a material kickback. − * Sled - A fixture that is placed on top of the table to assist with cross cuts. The sled keeps material perpendicular to the blade and helps to prevent the blade from kicking back material. Line 61:
Line 57: − − − + − [[File:TABLE_SAW_CONTROLS.jpg|none|thumb|600x600px]] Line 82:
Line 75: − +
no edit summary
|Has imagedesc=Janome Mylock 634D
|Has imagedesc=Janome Mylock 634D
|Has description=
|Has description=
|Has certification=
|Has certification=https://georgefox.instructure.com/courses/1268
|Has make=Janome
|Has make=Janome
|Has model=MyLock 364D
|Has model=MyLock 634D
|Has serial number=6E1013527
|Has serial number=6E1013527
|Has ace=Needed;Needed
|Has ace=Gail Dowler;gdowler@georgefox.edu
}}
}}
[[{{#show: {{FULLPAGENAME}}|?Has icon|link=none}}|140px|left|top|{{#show: {{FULLPAGENAME}}|?Has icondesc}}]]
[[{{#show: {{FULLPAGENAME}}|?Has icon|link=none}}|140px|left|top|{{#show: {{FULLPAGENAME}}|?Has icondesc}}]]
Location: {{#show: {{PAGENAME}} |?Is located in facility}}
Location: {{#show: {{PAGENAME}} |?Is located in facility}}
__TOC__
__TOC__
==Documentation==
==Documentation==
[[Media:Inst-book-634d.pdf|Serger User Manual]]
* [https://www.janome.com/machines/sergers/mylock-634d/ Product Home Page]
* [https://www.janome.com/machines/sergers/mylock-634d/ Product Home Page]
====Terminology====
====Terminology====
* Rip - Cuts made along the length of the wood.
* Needle -
* Cross-cut - Cuts made across the grain along the shorter side of the wood.
* Spool -
==Training==
==Training==
{{#evu:https://www.youtube.com/watch?v=oQww9QqVwOw}}
{{#evu:https://www.youtube.com/watch?v=oQww9QqVwOw}}
<br />
<br />
Sergers are great for adding zippers into your project. Here is a helpful video to lead you through the process.
Sergers are great for adding zippers into your project. Here is a helpful video to lead you through the process.
<br />
<br />
{{#evu:https://www.youtube.com/watch?v=b4SFacsuH1k}}
{{#evu:https://www.youtube.com/watch?v=b4SFacsuH1k}}
<br /><br /><br /><br /><br />
<br /><br /><br /><br /><br />
====Demonstration====
====Demonstration====
Demonstrate you can safely setup the saw and rip a board. You will then proceed to cross cut one of the remaining pieces. Remember to set the blade height so it is protruding less than 1/4" out the top of material for less exposure. When performing a rip cut the fence is used to guide the lumber into the blade. You want to make sure that the distance between the fence and blade is the width of desired cut. Mark the edge of the material when doing a cross cut so you can align the material with the blade in the sled. You can also use a miter gauge for making cross cuts but make sure the material is long enough and well supported.
Demonstrate you can safely setup the serger. You will then proceed to edge a piece of scrap material.
====General Procedure====
====General Procedure====
==Safety==
==Safety==
==Certification==
==Certification==
[https://foxtale.georgefox.edu/moodle/course/view.php?id=31427 Foxtale Course]
[https://georgefox.instructure.com/courses/1268 Canvas Quiz]
==Troubleshooting==
==Troubleshooting==