Difference between revisions of "Ring Roller"
| Line 5: | Line 5: | ||
|Is used in domain=Metal | |Is used in domain=Metal | ||
|Has name={{PAGENAME}} | |Has name={{PAGENAME}} | ||
| − | |Has make=Baileigh | + | |Has make=Baileigh Industrial |
|Has model=R-M5 | |Has model=R-M5 | ||
| + | |Has serial number=US14464115 | ||
|Has function=Ring Roller | |Has function=Ring Roller | ||
|Has icon=File: Ring_rollerIcon.png | |Has icon=File: Ring_rollerIcon.png | ||
| Line 15: | Line 16: | ||
|Has ace=Noah Bloomquist; nbloomquist17@georgefox.edu | |Has ace=Noah Bloomquist; nbloomquist17@georgefox.edu | ||
}} | }} | ||
| − | [[{{#show: {{FULLPAGENAME}}|?Has icon|link=none}}| | + | [[{{#show: {{FULLPAGENAME}}|?Has icon|link=none}}|140px|left|top|{{#show: {{FULLPAGENAME}}|?Has icondesc}}]] |
[[{{#show: {{FULLPAGENAME}}|?Has image|link=none}}|275px|thumb|upright=1.0|{{#show: {{FULLPAGENAME}}|?Has imagedesc}}]] | [[{{#show: {{FULLPAGENAME}}|?Has image|link=none}}|275px|thumb|upright=1.0|{{#show: {{FULLPAGENAME}}|?Has imagedesc}}]] | ||
| Line 21: | Line 22: | ||
Model: {{#show: {{PAGENAME}} |?Has model}} | Model: {{#show: {{PAGENAME}} |?Has model}} | ||
| + | |||
| + | Serial Number: {{#show: {{PAGENAME}} |?Has serial number}} | ||
Ace: {{#show: {{PAGENAME}} |?Has ace.Has name}} ({{#show: {{PAGENAME}} |?Has ace.Has email address}}). | Ace: {{#show: {{PAGENAME}} |?Has ace.Has name}} ({{#show: {{PAGENAME}} |?Has ace.Has email address}}). | ||
Revision as of 10:55, 10 August 2020
Make: Baileigh Industrial
Model: R-M5
Serial Number: US14464115
Ace: Luke Roderick (lroderick20@georgefox.edu).
Location: Machine Shop
Description
A ring roller is a machine used to roll metal into a ring by forcing the material through rollers, also called dies. The rollers can be adjusted to change the formed radius. The maximum mild steel machine capacity is 1/4" x 1" flat bar or 1/2" round rod. The minimum diameter you can form is 2.75"
Here is an example of this piece of equipment being used.
Documentation
Terminology
- Dies - Round pieces of steel used to guide the material as its shaped.
Manual Media:R-M5_07-2019.pdf
Training
Operation
Insert Text
Demonstration
Demonstrate you can safely setup the Ring Roller. You will then proceed to cut a 5" long piece of 1/4" steel rod. Roll this material into the smallest radius possible. When rolling the material remember to keep your fingers away from the rollers to keep from smashing your fingers.
General Procedure
- Adjust the knob on the right to adjust the radius, loosen the handle on the left if it restricting you from adjusting the right one.
- Make sure both knobs are secure and tightened before rolling, always start by rolling the largest radius, and work your way up from there.
- Insert the bar between the rollers.
- Turn the crank to roll the metal bar or rod.
- Start with a large radius and continue to make the radius smaller every time you roll. If you attempt to roll a small radius all at once, the rod may make a corkscrew shape instead of a circle.
- You have completed the roll when the two ends overlap each other by a couple of inches to account for the ends of the bar or rod that stay straight.
Safety
Insert text
Certification
Foxtale Quiz
Troubleshooting
Maintenance
General maintenance
Insert text
Specific Maintenance Tasks
| Maintenance Procedure | Frequency | Done By |
|---|---|---|
| Sample | Sample | Sample |