124
edits
Changes
Jump to navigation
Jump to search
Line 14:
Line 14: − + Line 28:
Line 28: + + + + + + + + + + + Line 42:
Line 53: + + Line 59:
Line 72: − + − + + Line 83:
Line 97: − − ==Safety== − # '''NEVER''' allow your hands/fingers to enter the infeed opening. − # '''NEVER''' turn on the Thickness Planer with stock inside the infeed opening. No good. − # '''NEVER''' bend down to look into a planer while it is running. − # '''NEVER''' attempt to repair the machine or remove any panels. − # '''NEVER''' put your finger in a knot hole while operating the Thickness Planer.
→General Procedure
|Has model=209HH-3
|Has model=209HH-3
|Has serial number=1706209HH5185
|Has serial number=1706209HH5185
|Has ace=Logan Hanbey;lhanbey17@georgefox.edu
|Has ace=Needed;Makerhub@georgefox.edu
}}
}}
[[{{#show: {{FULLPAGENAME}}|?Has icon|link=none}}|140px|left|top|{{#show: {{FULLPAGENAME}}|?Has icondesc}}]]
[[{{#show: {{FULLPAGENAME}}|?Has icon|link=none}}|140px|left|top|{{#show: {{FULLPAGENAME}}|?Has icondesc}}]]
Location: {{#show: {{PAGENAME}} |?Is located in facility}}
Location: {{#show: {{PAGENAME}} |?Is located in facility}}
__TOC__
__TOC__
==Safety First==
[[File:Safety First HD2.png|left|150px]]
* '''NEVER''' allow your hands/fingers to enter the infeed opening.
* '''NEVER''' turn on the Thickness Planer with stock inside the infeed opening. No good.
* '''NEVER''' bend down to look into a planer while it is running.
* '''NEVER''' attempt to repair the machine or remove any panels.
* '''NEVER''' put your finger in a knot hole while operating the Thickness Planer.
==Description==
==Description==
====Terminology====
====Terminology====
[[File:...Planer.png|none|thumb|500x500px]]
[[File:...Planer.png|none|thumb|500x500px]]
[[Media:1791296 man EN.pdf|Planer User Manual]]
[http://www.powermatic.com/us/en/p/209hh-20-planer-5hp-3ph-230-460v/1791316 Vendor Website]
[http://www.powermatic.com/us/en/p/209hh-20-planer-5hp-3ph-230-460v/1791316 Vendor Website]
File:Large Dust Collector Image.jpg|Large Dust Collector
File:Large Dust Collector Image.jpg|Large Dust Collector
</gallery>
</gallery>
# Before turning on the machine, loosen the table lock nuts on the side of the machine. slide the material into the machine and slowly adjust the table height by rotating the handwheel until the material
# Make sure the material is free of all foreign objects, loose knots, and splits
# The key is to take off very little material on the first pass and adjust as needed.
# Before turning on the machine, loosen the table lock nuts on the side of the machine. slide the material into the machine and slowly adjust the table height by rotating the handwheel until the material barely touches.
## The key is to take off very little material on the first pass and adjust as needed.
# Remove piece and adjust wheel to trim desired amount off of work piece.
# Remove piece and adjust wheel to trim desired amount off of work piece.
# Never attempt to remove more than 1/16” per pass (one turn). Do not over load the motor. Multiple passes result in less tear-out and are easier on the machine.
# Never attempt to remove more than 1/16” per pass (one turn). Do not over load the motor. Multiple passes result in less tear-out and are easier on the machine.
# Clean off the infeed table so that the next users’ stock will be able to make contact directly with the table instead of being raised up slightly by the chips left after you’re finished planing.
# Clean off the infeed table so that the next users’ stock will be able to make contact directly with the table instead of being raised up slightly by the chips left after you’re finished planing.
# Turn off and disconnect the dust collector.
# Turn off and disconnect the dust collector.
==Certification==
==Certification==