Line 15: |
Line 15: |
| |Has make=Voltera | | |Has make=Voltera |
| |Has serial number=V1-05-0129-120 / V1-04-0183-120 | | |Has serial number=V1-05-0129-120 / V1-04-0183-120 |
− | |Has ace=Needed;Needed | + | |Has ace=Needed;Makerhub@georgefox.edu |
| }} | | }} |
| [[{{#show: {{FULLPAGENAME}}|?Has icon|link=none}}|140px|left|{{#show: {{FULLPAGENAME}}|?Has icondesc}}]] | | [[{{#show: {{FULLPAGENAME}}|?Has icon|link=none}}|140px|left|{{#show: {{FULLPAGENAME}}|?Has icondesc}}]] |
Line 75: |
Line 75: |
| File:Voltera burnish.jpg|Burnishing Pads | | File:Voltera burnish.jpg|Burnishing Pads |
| </gallery> | | </gallery> |
| + | |
| + | [[Media:Voltera_V-One_Manual_English.pdf|Voltera User Manual]] |
| | | |
| [https://support.voltera.io/circuit-design-guidelines Circuit Design Guidelines] | | [https://support.voltera.io/circuit-design-guidelines Circuit Design Guidelines] |
Line 81: |
Line 83: |
| | | |
| [https://www.voltera.io/ Voltera Home Page] | | [https://www.voltera.io/ Voltera Home Page] |
− |
| |
− | [https://www.voltera.io/docs/downloads/manuals/Voltera%20V-One%20Manual%20%5BEnglish%5D.pdf User Manual]
| |
| | | |
| [https://support.voltera.io/hc/en-us/sections/115001325748-User-Guides User Guides] | | [https://support.voltera.io/hc/en-us/sections/115001325748-User-Guides User Guides] |
Line 140: |
Line 140: |
| #'''Ready the Ink''' | | #'''Ready the Ink''' |
| ##The ink is most usable when it reaches room temperature, so we have to let it warm up in advance. | | ##The ink is most usable when it reaches room temperature, so we have to let it warm up in advance. |
− | ##Reference the [[#Current Inks and Paste|Current Inks and Paste]] for information on the what the PCB lab is currently stocked with.
| |
| ##Grab the correct conductive ink from the fridge, and let it warm up to room temperature, about 15-30 minutes. It is labeled with a '''green''' sticker. | | ##Grab the correct conductive ink from the fridge, and let it warm up to room temperature, about 15-30 minutes. It is labeled with a '''green''' sticker. |
| #'''Software Setup''' | | #'''Software Setup''' |
Line 164: |
Line 163: |
| #'''Priming the Conductor''' | | #'''Priming the Conductor''' |
| ##Ensure 15 minutes have passed before beginning the next step. This helps the ink flow easier, so the dispenser should not be cold to the touch. | | ##Ensure 15 minutes have passed before beginning the next step. This helps the ink flow easier, so the dispenser should not be cold to the touch. |
− | ##'''Read carefully.''' The Voltera application explains this step well. Follow the on-screen instructions before moving on to the next step. Some tips/tricks/warnings: <br /><br /> - '''Nozzles are fragile!''' You would be surprised how easy it is to break one. Treat this process with care!<br /> - Hold the dispenser over a paper towel to prevent ink from getting everywhere.<br /> - If you need to wipe the nozzle, do so '''gently''' and '''use a cotton swab found in the drawers.''' <br /> - Ink should not be flowing quickly out of the dispenser when you finish priming, but '''a very small amount''' of flow is OK. <br /> [[File:Voltera priming.jpg|border|none|300x300px]] | + | ##'''Read carefully.''' The Voltera application explains this step well. Follow the on-screen instructions before moving on to the next step. Some tips/tricks/warnings:<br /> - '''Nozzles are fragile!''' You would be surprised how easy it is to break one. Treat this process with care!<br /> - Hold the dispenser over a paper towel to prevent ink from getting everywhere.<br /> - If you need to wipe the nozzle, do so '''gently''' and '''use a cotton swab found in the drawers.''' <br /> - Ink should not be flowing quickly out of the dispenser when you finish priming, but '''a very small amount''' of flow is OK. <br /> [[File:Voltera priming.jpg|border|none|300x300px]] |
| ##Mount the dispenser. [[File:Voltera mount_conductive.jpg|border|none|300x300px]] | | ##Mount the dispenser. [[File:Voltera mount_conductive.jpg|border|none|300x300px]] |
| #'''Calibration''' | | #'''Calibration''' |
Line 181: |
Line 180: |
| ##When you reach the instruction titled "Flip Board," you are done. We want to bake these traces on the Reflow Oven before we do anything else to the board. | | ##When you reach the instruction titled "Flip Board," you are done. We want to bake these traces on the Reflow Oven before we do anything else to the board. |
| ##Unclamp the board from the Voltera, and remember that the traces are still wet, so do not smear them around. | | ##Unclamp the board from the Voltera, and remember that the traces are still wet, so do not smear them around. |
− | ##Consult the Reflow Oven wiki and complete that process. | + | ##Consult the Reflow Oven wiki and complete that process. Bake the board soon after printing to ensure best results. |
| #'''Preparing for Solder Paste''' | | #'''Preparing for Solder Paste''' |
| ##You should now have a PCB with traces baked on it! Time to make those pads for placing components. | | ##You should now have a PCB with traces baked on it! Time to make those pads for placing components. |
Line 221: |
Line 220: |
| ==Certification== | | ==Certification== |
| | | |
− | [https://georgefox.instructure.com/courses/1288 Canvas Quiz] | + | [https://georgefox.instructure.com/courses/1291 Canvas Quiz] |
| | | |
| ==Troubleshooting== | | ==Troubleshooting== |
Line 248: |
Line 247: |
| |General Cleaning | | |General Cleaning |
| |Before and after each use, including ink/solder residue and drilled material | | |Before and after each use, including ink/solder residue and drilled material |
| + | |Student |
| + | |N/A |
| + | |- |
| + | |Refrigerating the Dispensers |
| + | |Whenever they are not in use |
| |Student | | |Student |
| |N/A | | |N/A |
Line 259: |
Line 263: |
| |When the nozzle is clogged | | |When the nozzle is clogged |
| |Student or Ace | | |Student or Ace |
− | |
| |
− | |-
| |
− | |Refrigerating the Dispensers
| |
− | |Whenever they are not in use
| |
− | |Student
| |
− | |N/A
| |
− | |-
| |
− | |Switch Cleaning
| |
− | |During Calibration stage using Isopropyl Alcohol and a giant Q-tip
| |
− | |Student
| |
| | | | | |
| |- | | |- |
Line 274: |
Line 268: |
| |Whenever out of ink/solder paste | | |Whenever out of ink/solder paste |
| |Ace | | |Ace |
− | | | + | | 01/27/2022 by MM |
| |- | | |- |
| |Labeling dispenser with lot name | | |Labeling dispenser with lot name |
| |Whenever ink/solder paste is replaced | | |Whenever ink/solder paste is replaced |
| |Ace | | |Ace |
− | | | + | | 01/27/2022 by MM |
| |- | | |- |
| |Cleaning calibration switch linear hardware (Disassemble, clean, oil) | | |Cleaning calibration switch linear hardware (Disassemble, clean, oil) |
| |Once yearly, or as required. | | |Once yearly, or as required. |
| |Ace and Technician | | |Ace and Technician |
− | | | + | | 01/27/2022 by MM |
| |} | | |} |