Changes

The press consists of a pump and hydraulic ram that moves down towards the table as the handle is cycled.  The hydraulic press has a 58 mm diameter ram and can produce 30 tons of force. Some of the many uses including installation and removal of press fit parts as well as metal forming and punching.  The ram can also be powered using compressed shop air, but should never be attempted without the shop techs supervision.  The ram can be adjusted laterally as need to accommodate a specific part.  As long as the ram keeps moving the force will remain fairly low. When the cylinder stops moving the hydraulic pressure in the system will start to build. As the force increases so does the risk. Pieces that are subjected to a high amount of force can shatter or explode. Make sure you are aware of what is happening and don't keep pumping on the handle and increasing the force without knowing what is occurring.

The press consists of a pump and hydraulic ram that moves down towards the table as the handle is cycled.  The hydraulic press has a 58 mm diameter ram and can produce 30 tons of force. Some of the many uses including installation and removal of press fit parts as well as metal forming and punching.  The ram can also be powered using compressed shop air, but should never be attempted without the shop techs supervision.  The ram can be adjusted laterally as need to accommodate a specific part.  As long as the ram keeps moving the force will remain fairly low. When the cylinder stops moving the hydraulic pressure in the system will start to build. As the force increases so does the risk. Pieces that are subjected to a high amount of force can shatter or explode. Make sure you are aware of what is happening and don't keep pumping on the handle and increasing the force without knowing what is occurring.

Make sure you have a full understanding of what you are attempting to accomplish before possibly getting into a risky situation. Ask a supervisor if you have any questions. Its important to properly set up the press before performing a job. It is good practice to observe the setup from various angles to ensure part alignment. If there is any risk something could fall on the floor during the process have a box or padding to catch the part. The table needs to be moved to the proper height to accommodate the work piece and ram travel. You want to avoid extending the ram farther than needed to prevent material from tipping over. Always make sure you will have enough ram travel to perform the task at hand. The release valve handle will need to be turned fully clockwise to allow the system to build pressure. It is imperative that you keep the work piece from tipping or slipping to the side while applying force to prevent flying parts and or damage. You should use a guide when pressing in a pin to prevent the pin or rod from slipping while installation. Keep an eye on the force gauge to verify your work piece is not sticking or hanging up. When the piece is pressed to its maximum travel pressure will start to build and could cause damage if you keep cycling the handle. Be aware that a part or piece could bottom out and avoid applying more force at the end of your parts travel than needed.

Make sure you have a full understanding of what you are attempting to accomplish before possibly getting into a risky situation. Ask a supervisor if you have any questions. Its important to properly set up the press before performing a job. It is good practice to observe the setup from various angles to ensure part alignment. If there is any risk something could fall on the floor during the process have a box or padding to catch the part. The table needs to be moved to the proper height to accommodate the work piece and ram travel.  The table plates have two sides.  One side is flat and the other has a V shape for holding round parts. The plates have a pin in each corner that prevent the plate from sliding off the table. You want to avoid extending the ram farther than needed to prevent material from tipping over. Always make sure you will have enough ram travel to perform the task at hand. The release valve handle will need to be turned fully clockwise to allow the system to build pressure. It is imperative that you keep the work piece from tipping or slipping to the side while applying force to prevent flying parts and or damage. You should use a guide when pressing in a pin to prevent the pin or rod from slipping while installation. Keep an eye on the force gauge to verify your work piece is not sticking or hanging up. When the piece is pressed to its maximum travel pressure will start to build and could cause damage if you keep cycling the handle. Be aware that a part or piece could bottom out and avoid applying more force at the end of your parts travel than needed.

====Demonstration====

====Demonstration====