1,947
edits
Changes
Jump to navigation
Jump to search
Line 92:
Line 92: − + Line 100:
Line 100: − + − + − + − + Line 121:
Line 121: − + − + + − + − + − + − + − + − + − + − + − +
→General Procedure
1. Place the plate you will be pressing the pin into on the top of the table frame support blocks.
1. Place the plate you will be pressing the pin into on the top of the table frame support blocks.
2. Set the dowel pin into the guide and make sure the table frame and support plates are high enough for the ram to be within an inch of the top of the pin.
2. Set the dowel pin into the guide and make sure the table frame and support plates are high enough for the ram to be within an inch of the top of the dowel pin.
[[File:HP Step 1.jpg|none|thumb]]
[[File:HP Step 1.jpg|none|thumb]]
4. To move the table frame down you will remove the two upper table support pins and reinstall them in the desired holes below.
4. To move the table frame down you will remove the two upper table support pins and reinstall them in the desired holes below.
5. You will need a second person to help lift the table frame slightly while removing the remaining two table support pins and slowly lower the table onto the pins below.
5. You will need a second person to help lift the table frame slightly while removing the remaining two table support pins and slowly lower the table onto the support pins below.
6. Reinstall the top two table support pins and safety clips.
6. Reinstall the top two table support pins and safety clips.
7. To move the table frame up you will leave the lower pins installed and remove the two upper pins. The lower pins will help prevent the table from accidentally dropping to the floor while making an adjustment.
7. To move the table frame up you will leave the lower support pins installed and remove the two upper support pins. The lower support pins will help prevent the table from accidentally dropping to the floor while making an adjustment.
8. You will need a second person to help lift the table frame while installing the two removed frame pins in the 2 lower positions.
8. You will need a second person to help lift the table frame while installing the two removed support pins in the 2 lower positions.
9. Install the 2 remaining top frame pins and safety clips.
9. Install the 2 remaining top support pins and safety clips.
10. Place table support plates and assembly pieces back onto the table.
10. Place table support plates and assembly pieces back onto the table.
14. Slowly pump the handle while watching the force gauge and the pin. Make sure pressure is not building.
14. Slowly pump the handle while watching the force gauge and the pin. Make sure pressure is not building.
15. If the pin starts at an angle do NOT continue to apply force as this will most likely bend the pin and cause damage.
15. If the pin starts at an angle do NOT continue to apply force as this could cause the dowel pin to slip sideways or damage the hole where the dowel presses into.
16. When the pin is at the bottom of its travel it will stop moving and you will see the force increase on the gauge and this is a good time to stop cycling the handle.
16. When the dowel pin is pressed to the bottom of the hole in the block it will contact the support plate and no longer be able to move. The bottoming out of the dowel pin will cause the force to increase on the gauge. Stop cycling the handle when the dowel pin reaches this point.
[[File:HP Step 5.jpg|none|thumb]]
[[File:HP Step 5.jpg|none|thumb]]
17. Turn the pressure relief handle counterclockwise to retract the ram as needed.
'''Pin Removal'''
'''Pin Removal'''
1. Place the plate with the installed pin (facing downward) on top of the table support plates. You will need to leave a gap between the plates for the pin to press though.
1. Place the plate with the pressed in dowel pin (facing downward) on top of the table support plates. You will need to leave a gap between the table plates for the pin to press though.
[[File:HP Step 6.jpg|none|thumb]]
[[File:HP Step 6.jpg|none|thumb]]
2. Check the distance between the pin extraction tool and the ram. If the gap is too large the ram will run out of travel before pressing out the pin.
2. Check the distance between the pin extraction tool and the ram. If the gap is too large the ram will run out of travel before pressing out the dowel pin.
[[File:HP Step 8.jpg|none|thumb]]
[[File:HP Step 8.jpg|none|thumb]]
3. If you need to adjust the table frame height remove the safety clips from the frame pins supporting the table and remove the table plates and assembly pieces. Remove everything from the table to prevent accidentally dropping items on your feet.
3. If you need to adjust the table frame height remove the safety clips from the frame support pins supporting the table. Remove everything from the table to prevent accidentally dropping items on your feet.
4. To move the table frame down you will remove the two upper pins and reinstall them in the correct holes below.
4. To move the table frame down you will remove the two upper support pins and reinstall them in the desired holes below.
5. You will need a second person to help lift the table frame slightly while removing the remaining two pins and slowly lower the table onto the pins below.
5. You will need a second person to help lift the table frame slightly while removing the remaining two support pins and slowly lower the table onto the support pins below.
6. Reinstall the top two pins and safety clips.
6. Reinstall the top two support pins and safety clips.
7. To move the table frame up you will leave the lower pins installed and remove the two upper pins. The lower pins will help prevent the table from accidentally dropping to the floor while making an adjustment.
7. To move the table frame up you will leave the lower support pins installed and remove the two upper support pins. The lower support pins will help prevent the table from accidentally dropping to the floor while making an adjustment.
8. You will need a second person to help lift the table frame while installing the two removed pins in the 2 lower positions.
8. You will need a second person to help lift the table frame while installing the two removed support pins in the 2 lower positions.
9. Install the 2 remaining top pins and safety clips.
9. Install the 2 remaining top support pins and safety clips.
10. Place table support plates and assembly pieces back onto the table.
10. Place table support plates and assembly pieces back onto the table.