Changes

{{#set:

{{#set:

  |Is equipment=True

  |Is equipment=True

  |Has make=Ellis

  |Has make=Ellis Mfg. Company Inc.

  |Has model=1600

  |Has model=1600

  |Has name={{PAGENAME}}

  |Has name={{PAGENAME}}

  |Is located in facility= Machine Shop

  |Is located in facility= Machine Shop

  |Is used in domain=Metal

  |Is used in domain=Metal

  |Has function=Horizontal Bandsaw

  |Has function=Horizontal Bandsaw

  |Has url=http://www.ellissaw.com/mitre-band-saw-overview/1600-mitre-band-saw/

  |Has url=http://www.ellissaw.com/mitre-band-saw-overview/1600-mitre-band-saw/

  |Has icon=File:horizontal_bandsaw_icon.png

  |Has icon=File:horizontal_bandsaw_icon.png

  |Has description=Used to cut large stock

  |Has description=Used to cut large stock

  |Has QR code=File:Horizontal Bandsaw QR code.png

  |Has QR code=File:Horizontal Bandsaw QR code.png

  |Has ace=Noah Bloomquist; nbloomquist17@georgefox.edu

  |Has ace=Needed; Makerhub@georgefox.edu

}}

}}

[[{{#show: {{FULLPAGENAME}}|?Has icon|link=none}}|100px|left|top|{{#show: {{FULLPAGENAME}}|?Has icondesc}}]]

[[{{#show: {{FULLPAGENAME}}|?Has icon|link=none}}|140px|left|top|{{#show: {{FULLPAGENAME}}|?Has icondesc}}]]

[[{{#show: {{FULLPAGENAME}}|?Has image|link=none}}|300px|thumb|upright=1.5|{{#show: {{FULLPAGENAME}}|?Has imagedesc}}]]

[[{{#show: {{FULLPAGENAME}}|?Has image|link=none}}|300px|thumb|upright=1.5|{{#show: {{FULLPAGENAME}}|?Has imagedesc}}]]

Make: {{#show: {{PAGENAME}} |?Has make}}

Make: {{#show: {{PAGENAME}} |?Has make}}

Model: {{#show: {{PAGENAME}} |?Has model}}

Model: {{#show: {{PAGENAME}} |?Has model}}

Ace: {{#show: {{PAGENAME}} |?Has ace.Has name}} ({{#show: {{PAGENAME}} |?Has ace.Has email address}}).

Ace: {{#show: {{PAGENAME}} |?Has ace.Has name}} ({{#show: {{PAGENAME}} |?Has ace.Has email address}}).

==== User Manual ====

==== User Manual ====

* [[Media:Ellis_1600_Safety.pdf|Ellis 1600 Safety PDF]]

 

* [https://maker-hub.georgefox.edu/w/images/b/b6/Ellis_1600_Manual.pdf Installation and Operating Instructions]

 

[[Media:Ellis_1600_Safety.pdf|Ellis 1600 Safety PDF]]

 

[[Media:Horz_Bandsaw_Tension.pdf|Blade Tensioning Guide]]

==Training==

==Training==

====Overview====

====Operation====

The first thing you will want to do is mark your stock where it should be cut. Once that is done place the material on the saw table and lower the blade to just above the material so you can accurately line the saw blade up with the mark on the material. If you are cutting rectangular stock make sure the longer side is the one on table. This allows more of the blade teeth to engage the material and lowers the stress on the blade as a result. To lower the blade, hold the handle on the idler wheel end of the saw with one hand and then open the hydraulic feed control by twisting the knob counterclockwise with the other hand. Lower the bade to just above the material and the close the feed control to hold the blade in place. Line up the your mark and saw blade but don't forget about the blade kerf if you are concerned about accuracy. Clamp the material in place with the vice and apply some oil to the cut area. You are now ready to cut. Press the green button to turn on the saw and then open the feed control slightly, causing the blade to slowly drop and perform the cut. The saw will automatically turn of when the cut is complete, but if you need to stop the saw during the cut press the red emergency stop button. Reset the space when you are done. All shavings should be cleaned up and disposed of properly. Put any extra stock back in its respective spot. When finished, make sure the blade arm is laying completely down so that the auto shutoff switch is engaged and no one can fit anything under the blade without raising the arm.  

The first thing you will want to do is mark your stock where it should be cut. Once that is done place the material on the saw table and lower the blade to just above the material so you can accurately line the saw blade up with the mark on the material. If you are cutting rectangular stock make sure the longer side is the one on table. This allows more of the blade teeth to engage the material and lowers the stress on the blade as a result. To lower the blade, hold the handle on the idler wheel end of the saw with one hand and then open the hydraulic feed control by twisting the knob counterclockwise with the other hand. Lower the bade to just above the material and then close the feed control to hold the blade in place. Line up your mark with the saw blade but don't forget about the blade kerf if you are concerned about accuracy. Clamp the material in place with the vice and apply some oil to the cut area. You are now ready to cut. Press the green button to turn on the saw and then open the feed control slightly and keep one hand on the handle of the machine head to slowly lower the blade.  Once the blade has a cut the depth of the teeth you can let go and gravity will feed the saw. The saw will automatically turn off when the cut is complete, but if you need to stop the saw during the cut press the red emergency stop button. Reset the space when you are done. All shavings should be cleaned up and disposed of properly. Put any extra stock back in its respective spot. When finished, make sure the blade arm is laying completely down so that the auto shutoff switch is engaged and no one can fit anything under the blade without raising the arm.

====Demonstration====

====Demonstration====

Cut a 1” long piece of ½” round stock.

Cut a 1.375” long piece of 1” aluminum round stock for the lathe demonstration part.

====General Procedure====

====General Procedure====

==Certification==

==Certification==

[https://foxtale.georgefox.edu/moodle/course/view.php?id=30475 Foxtale Quiz]

[https://georgefox.instructure.com/courses/1265 Canvas Quiz]

==Troubleshooting==

==Troubleshooting==