Finishing Room

From maker-hub
Jump to navigation Jump to search

The Finishing Room is a well ventilated room that is a great place for dirty work, painting, staining, sanding, using epoxy, etc.

The Prototype Lab

The current Aces of the Finishing Room are Needed (Makerhub@georgefox.edu).

Equipment Overview

3 commandments

1. Safety First

Safety First is the rule we hold highest of the three. This rule applies to both the safety of you as well as others

Keeping yourself safe in the Finishing Room is very important, as there are possibilities for accidents if you don't follow the safety guidelines.

The following rules must be followed at all times.

  • Safety glasses must be worn at all times.
  • Read the label of any paints or chemicals in use and understand what you are doing.
  • No horseplay in the room.
  • Don’t do anything distracting to yourself or others while working in the room.
  •  No open toed shoes.
  •  Hair will not extend bellow the collar.
  • Food or drink is not allowed in the Finishing Room.
  • Do not attempt to operate equipment that you have not been certified on by GFU engineering personnel.
  • Do not argue with volunteers or shop staff. Contact Justin Johnson if you have issues that need to be resolved.
  • You should have a buddy in the shop if you are using the room.
  • Reset the space. A clean space is a safer space.
  • If you see a safety violation inform the person immediately and encourage them to comply with the policies.
  • Don’t do anything that would require an additional rule to be added to this list.

2. Reset the Space

The Finishing Room has a specific organization to it. Put whatever you use back where it belongs. There is a place for everything and everything has a place. This rule applies to everything in the space. If you use a tool, put it back. If you use a pen, put it back. Do not leave your projects in the room unless you have made prior arrangements. Throw away your trash and recycling.

Now, we understand that sometimes you need to leave projects out. Maybe you are in the middle of a large project and the paint needs to dry overnight. In cases like this, it is okay, but you NEED to make prior arrangements with Nick or Justin.

Please put back the equipment the way you found it. The compressed air line should be coiled up neatly. Always put any unused materials back on the storage shelf, and throw away unusable scrap.

Pick up and used paint cans or rags.

Make sure to shut off the lights and room ventilation before leaving.

Always leave the space better than you found it.

3. Be Professional

This commandment has two sides to it. It covers the idea of acting like professional (which Webster’s defines as “exhibiting a courteous, conscientious, and generally businesslike manner in the workplace”). The term also describes the standards of education and training that prepare members of the profession with the particular knowledge and skills necessary to perform their specific role within that profession. Hopefully, you are learning both of these as part of your education at George Fox University. In the Welding Lab we expect you to develop as a courteous, conscientious, and skilled craftsman, understanding the tools and equipment in the Maker Hub and how to use them effectively.

Being a professional has some obvious ramifications in terms of behavior. First, be Christlike. Think of others better than yourselves. Share. If you have been welding for a prolonged time and someone else is waiting for the machine, let them use the machine for a while. This is being a professional.

If you are learning to paint or sand, and you can't get something to work the way you want - ASK SOMEONE! Learn! Become a professional. Learn the craft. This is an educational space. You might think it will be quick and you can just get it done “your” way and not learn how to do it correctly. Be a Professional and learn the proper way, and then be available to teach others.

One very important, and likely difficult part of being a professional is to correct others when they are not being professional. It is your responsibility to speak up when you see somebody doing something inappropriate. If you see somebody doing something unsafe, not resetting the space, or being unprofessional, the professional thing to do is to remind them of the three commandments and ask them politely to correct their action. This is OUR space, not any individual's. As a group, we expect everyone in the space to keep the space safe, clean, and operable for everyone. 

If someone acts disgracefully unprofessional to you in the Welding Lab, you are welcome to bring the issue to Justin or Nick's attention.

General Finishing Room Knowledge

The finishing room serves multiple functions. It can be used to paint in, sand and stain as well as other uses.


These are a few good steps to having a success using the Finishing Room.

  • Make sure you read the label of any paints or chemicals you are working with and understand the dangers.
  • Make sure the fan is turned on and pulling air.

Here are a couple things to keep in mind:

  • Material will be very hot after welding so always think before touching.
  • Make sure the welder is properly grounded before attempting to weld.
  • Never weld in wet clothes or around water.
  • Never try to weld any type of tank that has ever held flammable liquids. This is very dangerous and can explode!
  • Always check your welding hood settings prior to welding. (start with a darker setting and work your way down.
  • Welding takes lots of practice so don't be afraid to ask for help.


FDM Printing

Fused Deposition Modeling (FDM) printers use a thermoplastic filament, which is heated to its melting point, then extruded to create layers which then build an object. There are many different types of FDM printers. Some use a modeling material and a support material, some just use a modeling material which when creating support will use a different style of layering that allows the filament to break off easily, some are able to use multiple filaments at once allowing for multicolored objects to be created.

 
Example of a filament spool for a FDM printer.

Both Stratasys printers (Dimension and F370) use soluble support filament (the support filament dissolves in a heated sodium hydroxide bath), the Prusa printers use only a model material, and the Markforge printer only uses model material as well (however it will layer another filament for extra support).

The filament for these printers comes in spools (basically thin plastic ropes that are wound up). The filament is fed through an extruder head, heated to the desired temperature, then extruded (similar to what happens with a hot glue gun).

FDM printers can work with various materials, in the Prototype Lab we mainly stick to ABS which is used by the Stratasys machines and PLA which is used by the Prusas. The Markforge uses a material called Onyx (nylon and plastic mix) and will layer in another filament such as Carbon Fiber, Kevlar, etc.




Foxtale Certification

Before working with any of the equipment in the prototype lab you will need to take the general lab quiz as well as the specific quiz for each machine you are trying to use. The enrollment code for all of the quizzes is MakerHub.


Equipment

3 commandments