148
edits
Changes
Jump to navigation
Jump to search
Line 73:
Line 73: + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + +
no edit summary
[[File:Chimes 9.png|200px|left]]
[[File:Chimes 9.png|200px|left]]
[[File:Chimes 10.png|1400px|none]]
[[File:Chimes 10.png|1400px|none]]
<br>
Using the same beginning circle, create another circular array with 5 instances
[[File:Chimes 26.png|1400px|none]]
<br>
<br>
<strong>Step 6:</strong> We are going to extrude this sketch to make the hanger using contours. While still in the sketch, select the “Extruded Boss/Base” command
The thickness will be the same as your material. In this TV we are using ¼” acrylic.
We want to extrude the outer circle and still have the holes cut out with a hollow center. SolidWorks may be smart and do this for you automatically, but if not, open the “Selected Contours” section in the sidebar and select the area between the two large circles. It should look the this:
[[File:Chimes 11.png|1400px|none]]
<br>
Hit the green check mark to create the 3D solid
[[File:Chimes 12.png|1400px|none]]
<br>
<br>
<strong>Step 7:</strong> Next we are going to create the center circle that will hit against the chimes. Normal to the top plane and start a new sketch with a circle centered at the origin. This one will be smaller with a diameter of 1 in
[[File:Chimes 13.png|1400px|none]]
<br>
This one needs a hole in the center. Create a small circle with a diameter of 0.05 in
[[File:Chimes 14.png|1400px|none]]
<br>
<br>
<strong>Step 8:</strong> When we extrude this circle, we want it to be lower than our holder, so we are going to use the “Offset” option.
Select “Extruded Boss/Base and in the sidebar change the “from” option from Sketch Plane to Offset. This offsets the beginning of the extrusion from the sketch plane. Enter an offset distance of 2 in, and an extrusion thickness of 0.25 in.
[[File:Chimes 15.png|1400px|none]]
<br>
<br>
<strong>Step 9:</strong> We are going to make the ornamental hanging piece that goes at the bottom. This can be any shape as long as it is about 1 in wide and no more than 2 in tall. I am going to make a teardrop diamond shape for mine.
The first step is to create a sketch in the front plane. Draw a construction line from the origin and down to about 2 inches below the center circle. (This is not specific since it is just for visualization)
[[File:Chimes 16.png|1400px|none]]
<br>
Draw your hanging shape at the end of the construction line.
[[File:Chimes 17.png|1400px|none]]
<br>
Extrude the piece the same ¼”, but this time change the direction 1 to “Mid-Plane”
[[File:Chimes 18.png|1400px|none]]
<br>
After finishing that piece, you have drawn each piece that you will be laser cutting and have a general idea of how it will look when hanging.
[[File:Chimes 19.png|1400px|none]]
<br>
<br>
<strong>Step 10:</strong> Since we are going to be cutting these pieces on the laser cutter, we need to export them as .dxf so the laser cutter program can read it.
Go to “File > Save as” and change the type to .dxf
We are going to have to do this twice since not all of our faces are parallel.
This will prompt you to select what view or faces you want to export. Select the “Faces/loops/edges” option and select the top faces of the two circle hangers.
[[File:Chimes 20.png|1400px|none]]
<br>
This will export those faces as 2D vectors that can be put into inkscape and prepared for cutting.
[[File:Chimes 21.png|1400px|none]]
<br>
Repeat these steps and select the front face of the hanger.
[[File:Chimes 22.png|1400px|none]]
[[File:Chimes 23.png|1400px|none]]
==Inkscape==
Next we are going to prepare our .dxf files for the Laser Cutter using Inkscape. This is about what the file should look like. Details for preparing the file and instructions for cutting the pieces can be found on the [[Laser Cutter]] wiki page.
As a note, all cut lines should be fully red (255,0,0) and all engraving should be fully black (0,0,0)
[[File:Chimes 24.png|1400px|none]]