Changes

====Overview====

====Overview====

The operation of the mug press is pretty simple. First, select a heating element that fits your glass or mug and fasten it into place using the black screws. There is no formula for selecting the correct element other than putting your mug inside and making sure it fits snug. Adjust the pressure using the large black knobs so that there is a firm, even pressure over the mug. Next, set the time and temperature. Feel free to experiment with different values as there is not an exact formula, but for the heat transfer vinyl that is commonly used on the vinyl printer anywhere between 300°F and 325°F for 15 seconds works well. If the graphic begins to peel off when removing the paper then the time should be increased and if the graphic colors change when being applied the temperature should be decreased. Also it is important to use the Teflon sheets found in the t shirt heat press to prevent sticking to the heating element if using the plastic transfer paper. After the time and temperature are set place the mug in the element and clamp down. The timer will beep once the transfer is complete. For complete details see the general procedure.  

The operation of the mug press is pretty simple. First, select a heating element that fits your glass or mug and fasten it into place using the black screws. There is no formula for selecting the correct element other than putting your mug inside and making sure it fits snug. Adjust the pressure using the large black knobs so that there is a firm, even pressure over the mug. Next, set the time and temperature. Feel free to experiment with different values as there is not an exact formula, but for the heat transfer vinyl that is commonly used on the vinyl printer anywhere between 350°F and 385°F for 120 seconds works. If the graphic begins to peel off when removing the paper then the time should be increased and if the graphic colors change when being applied the temperature should be decreased. Also it is important to use the Teflon sheets found in the t shirt heat press to prevent sticking to the heating element if using the plastic transfer paper. After the time and temperature are set place the mug in the element and clamp down. The timer will beep once the transfer is complete. For complete details see the general procedure.  

====Demonstration====

====Demonstration====

# Use the black set screws to secure the heating element into the press and plug it into the controller. Make sure to screw in the plug as well to ensure a good connection.

# Use the black set screws to secure the heating element into the press and plug it into the controller. Make sure to screw in the plug as well to ensure a good connection.

# Once the heating element is installed you will want to adjust the pressure applied to the mug using the four large pressure adjustment knobs. The pressure should be evenly distributed across the mugs's surface and firm without risk of crushing it.  

# Once the heating element is installed you will want to adjust the pressure applied to the mug using the four large pressure adjustment knobs. The pressure should be evenly distributed across the mugs's surface and firm without risk of crushing it.  

# Adjust the time and temperature. 305 °F for 15 seconds is recommended as a starting point but feel free to try new things to improve the results. See the image below for details on changing the time and temp. [[File:Mug press temp.png|none|thumb|799x799px]]

# Adjust the time and temperature. 385 °F for 120 seconds is recommended as a starting point but feel free to try new things to improve the results. See the image below for details on changing the time and temp. [[File:Mug press temp.png|none|thumb|799x799px]]

# Place the graphic onto the mug. Tape may be helpful so that the graphic does not shift after it is placed into the press..

# Place the graphic onto the mug. Tape may be helpful so that the graphic does not shift after it is placed into the press. Do not use the plastic transfer paper for mug applications because it will melt due to the extended time it takes to apply. Instead print your graphic mirrored and leave it on the vinyl backing when applying.  

# Put the mug into the press and clamp down. If a plastic transfer paper is being used make sure to wrap the entire mug in one of the Teflon sheets found in the t shirt heat press to prevent the transfer paper from melting to the heating element. The timer will beep once the transfer is complete.

# Put the mug into the press and clamp down until the timer beeps.

# Remove the mug from the press and wait about 30 seconds before removing the transfer paper.  

# Remove the mug from the press and wait about 30 seconds before removing the paper.  

# Reset the space by turning off the machine, throwing away any scraps and wiping any debris off the machine.

# Reset the space by turning off the machine, throwing away any scraps and wiping any debris off the machine.

==Safety==

==Safety==

* Things are muy calinte.  

* This machine uses heat to operate so be aware of the heating element when it is running to avoid burns.

* Do n

* Do not leave the heating element on any longer than necessary if there is nothing inside it. Long periods of time without something in the press can damage the heating element.

==Certification==

==Certification==