Difference between revisions of "Serger"

Revision as of 14:30, 26 January 2023

Janome Mylock 634D

Make: Janome

Model: MyLock 634D

Serial Number: 6E1013527

Ace: Needed (Justinj@georgefox.edu).

Location: The Hub

Safety First

Here are some safety instructions for the Serger. Remember... SAFETY FIRST!!!

Sharp Hazard – needles are very sharp and can pierce your skin. Turn off the serger when inserting/removing needles to avoid bumping the foot pedal and moving the needle assembly. Never place your fingers directly underneath the needle.
Crush Hazard – be aware of all moving parts and keep your fingers away from any pinch points.
Entanglement – ensure that loose clothing, long hair, or any other dangling/loose items do not become entangled in the machine. Hair that extends below the collar should be tied up.
Eye Injury – needles can break if they hit a solid object while sewing. The broken tip can fly off and become lodged in your eye. Wear safety glasses when using the serger.
Do not sew over pins. This can break or bend the needle.
Always use the proper needle plate. The wrong plate can cause the needle to break.
Do not push or pull fabric while stitching. It may deflect the needle causing it to break.
Ensure the needle you are using is undamaged.
Make sure the needle is installed correctly.
Verify that you are using the correct presser foot. When changing out the presser foot, manually check that the needle’s travel will clear the foot before using the foot pedal.
Do not run thick fabrics or many layers of fabric through the serger. Use the industrial sewing machine for these applications.
When you finish using the serger, disconnect the power cable from both the machine and the wall outlet/power strip. Coil the power cable neatly on the table.

Description

Sergers preform a type of stitch known as overlock stitching. An overlock stitch is a type of stitching that sews over the edge of one or more pieces of fabric. Sergers also have the ability to cut off the excess edge as it is fed through the machine. This type of stitching is useful for edging, hemming, and seaming. This process will create a clean edge of your fabric that will not fray.

The Janome MyLock 634D features 2 needles and a choice of 2, 3, or 4 thread overlocking stitching. The color-coded thread guiding makes threading simple and easy to follow. The MyLock 634D allows the user to easily switch from overlock stitching to rolled hemming without needing to change to needle plate. Some of the key features of the MyLock 634D are a tension release device, easily accessible lower looper guides, changeable thread guide, easily retractable upper knife, adjustable foot pressure, and more.

Documentation

Serger User Manual

Product Home Page

Terminology

Needle -
Spool -

Training

Operation

All information on this specific machine can be found in the User Manual

A simple intro to serging:

Sergers are great for adding zippers into your project. Here is a helpful video to lead you through the process.

Demonstration

Demonstrate you can safely setup the serger. You will then proceed to edge a piece of scrap material.

General Procedure

Insert general procedure here.

Certification

Canvas Quiz

Troubleshooting

If are having issues ask the supervisor.

Maintenance

General maintenance

Keep the saw clean and use the dust collector. There are several lubrication points on the saw that need to be checked by the tech.

Specific Maintenance Tasks

Maintenance Procedure	Frequency	Done By
Lubricate mechanisms	As Needed	Technician
Clean machine	when Done	User
Change the needle	As Needed	User

@@ Line 38: / Line 38: @@
 [[File:Safety First HD2.png|left|150px]]
 Here are some safety instructions for the {{PAGENAME}}. Remember... SAFETY FIRST!!!
-*'''Fire / Burns''' – the propane torch emits an extremely hot open flame that can cause serious burns. Do not point the torch towards yourself or anyone else. Do not touch the nozzle or put your hands in front of the nozzle. Do not tip the torch sideways when annealing. Always make sure to close the valve and lock the trigger after you finish annealing. Be mindful that the needle nose pliers can be hot too after annealing. If you get burned, run cold water over the burned area for several minutes to reduce inflammation and the potential for blistering.
+*'''Sharp Hazard''' – needles are very sharp and can pierce your skin. Turn off the serger when inserting/removing needles to avoid bumping the foot pedal and moving the needle assembly. Never place your fingers directly underneath the needle.
-*'''Eye Injury''' – you must wear safety glasses throughout the annealing process and when swinging a hammer to punch out the center of a coin. Anyone else within a 6-foot radius should also wear safety glasses when you are annealing or hammering.
+*'''Crush Hazard''' – be aware of all moving parts and keep your fingers away from any pinch points.
-*'''Crush Hazard''' – exercise caution when using the press to fold your coin or using the stretcher/reducer. These tools have several pinch points and can cause serious injury to your hand if it gets caught between the moving parts.
+*'''Entanglement''' – ensure that loose clothing, long hair, or any other dangling/loose items do not become entangled in the machine. Hair that extends below the collar should be tied up.
-*'''Sharp Hazard''' – coins can have sharp burrs after punching a hole. Use the manual deburring tool to remove the sharp edge.
+*'''Eye Injury''' – needles can break if they hit a solid object while sewing. The broken tip can fly off and become lodged in your eye. Wear safety glasses when using the serger.
-*'''Corrosive Chemicals''' – the Midas Black Max finish contains hydrochloric acid which can cause severe skin burns and eye damage. A lab coat, chemical goggles, and gloves must be worn when handling hydrochloric acid. Consult the Maker Hub staff for proper disposal. Midas Black Max finish should only be applied to real silver/gold coins. All finishes must be applied in the Finishing Room to minimize your exposure to harmful vapors.
+*Do not sew over pins. This can break or bend the needle.
-*When punching out the center of a coin, place a wooden block on the floor with the punch assembly on top of it to protect the end of the punch from being damaged by the concrete.
+*Always use the proper needle plate. The wrong plate can cause the needle to break.
-*Ensure there is water in the pot before attempting to anneal your coin.
+*Do not push or pull fabric while stitching. It may deflect the needle causing it to break.
-*Don’t get a coin ring stuck on your finger.
+*Ensure the needle you are using is undamaged.
+*Make sure the needle is installed correctly.
+*Verify that you are using the correct presser foot. When changing out the presser foot, manually check that the needle’s travel will clear the foot before using the foot pedal.
+*Do not run thick fabrics or many layers of fabric through the serger. Use the industrial sewing machine for these applications.
+*When you finish using the serger, disconnect the power cable from both the machine and the wall outlet/power strip. Coil the power cable neatly on the table.
 ==Description==