Difference between revisions of "Miller Spectrum 875 Plasma Cutter"
Jump to navigation
Jump to search
(Created page with "blah blah blah") |
(Added to proposed deletion) |
||
| (8 intermediate revisions by one other user not shown) | |||
| Line 1: | Line 1: | ||
| − | + | [[Category:Proposed deletion]] | |
| + | |||
| + | {{#set: | ||
| + | |Is equipment= | ||
| + | |Is located in facility= | ||
| + | |Is used in domain= | ||
| + | |Has icon=File:image_pending.png | ||
| + | |Has icondesc=Add description | ||
| + | |Has iconwname= | ||
| + | |Has image=File:image_pending.png | ||
| + | |Has imagedesc=Image description here | ||
| + | |Has description=(???) | ||
| + | |Has certification=(???) | ||
| + | |Has make= Miller | ||
| + | |Has model= Spectrum 875 | ||
| + | }} | ||
| + | [[{{#show: {{FULLPAGENAME}}|?Has icon|link=none}}|100px|left|top|{{#show: {{FULLPAGENAME}}|?Has icondesc}}]] | ||
| + | [[File:Plas.jpg|thumb]] | ||
| + | <br />Miller Spectrum® 875 Plasma Cutter with 20 foot XT60 torch has compact size but 60 amps of output power. | ||
| + | |||
| + | It features easy operator controls, for optimum cutting and gouging performance. | ||
| + | |||
| + | |||
| + | = Documentation: = | ||
| + | https://www.millerwelds.com/files/owners-manuals/o242880c_mil.pdf | ||
| + | |||
| + | = Procedures: = | ||
| + | # Place fume hood over the area you will be welding at | ||
| + | # Turn air on | ||
| + | # Turn plasma cutter on | ||
| + | # Attach ground clamp | ||
| + | # Measure thickness of material being cut and refer to chart for current setting on machine | ||
| + | # Set the current on the plasma cutter | ||
| + | # Place the drag shield on the edge of the base metal, or hold ⅛ inch off the surface. Direct the arc straight down. | ||
| + | # Raise the trigger lock and press the trigger, this will engage the pilot arc | ||
| + | # Once the cutting starts, begin to slowly move the torch across the metal | ||
| + | # Adjust your speed so the sparks go thru the metal and out the bottom of the cut | ||
| + | # At the end of the cut, angle the torch slightly towards the final edge or pause briefly before releasing the trigger | ||
| + | # Turn off machine | ||
| + | # Turn off air | ||
| + | # Disconnect ground clamp | ||
| + | |||
| + | = Warnings: = | ||
| + | # Don't cut lead, zinc, copper, cadmium, stainless, or beryllium. | ||
| + | # Don't attempt to cut with the oxygen off | ||
| + | # Don’t cut with the vent hood off | ||
Latest revision as of 22:33, 27 January 2022
Miller Spectrum® 875 Plasma Cutter with 20 foot XT60 torch has compact size but 60 amps of output power.
It features easy operator controls, for optimum cutting and gouging performance.
Documentation:
https://www.millerwelds.com/files/owners-manuals/o242880c_mil.pdf
Procedures:
- Place fume hood over the area you will be welding at
- Turn air on
- Turn plasma cutter on
- Attach ground clamp
- Measure thickness of material being cut and refer to chart for current setting on machine
- Set the current on the plasma cutter
- Place the drag shield on the edge of the base metal, or hold ⅛ inch off the surface. Direct the arc straight down.
- Raise the trigger lock and press the trigger, this will engage the pilot arc
- Once the cutting starts, begin to slowly move the torch across the metal
- Adjust your speed so the sparks go thru the metal and out the bottom of the cut
- At the end of the cut, angle the torch slightly towards the final edge or pause briefly before releasing the trigger
- Turn off machine
- Turn off air
- Disconnect ground clamp
Warnings:
- Don't cut lead, zinc, copper, cadmium, stainless, or beryllium.
- Don't attempt to cut with the oxygen off
- Don’t cut with the vent hood off