Changes

Jump to navigation Jump to search
196 bytes added ,  4 years ago
Line 51: Line 51:  
The core of jointer consists of a round cutter head with many carbide cutters.  The cutter head is located between the in-feed and out-feed table.  The front table can be adjusted up and down to control the amount of material that is exposed to the cutter head. The lower the table the more material per pass will be removed. Don't try to adjust the out-feed table as the height has been set to support the material after it has been ran past the cutter head. Misalignment of the cutter head to out-feed table will create uneven cuts or jam the material on out-feed. There are a few other things to keep in mind regarding your material as well. Make sure the material you are cutting is free of all foreign objects. Do not cut materials that may have nails or screws as they will damage the blade and may cause injury to you. Also, if the material contains a loose knot it can break free and create a safety hazard. Only cut with the grain, attempting to cut across the grain of material will create poor results and could create kick-back. Do not attempt to joint end grain either. If you have a cupped board place the concave side down on the table while running it through the machine. This will help remove material on the ends and flatten out the board.  
 
The core of jointer consists of a round cutter head with many carbide cutters.  The cutter head is located between the in-feed and out-feed table.  The front table can be adjusted up and down to control the amount of material that is exposed to the cutter head. The lower the table the more material per pass will be removed. Don't try to adjust the out-feed table as the height has been set to support the material after it has been ran past the cutter head. Misalignment of the cutter head to out-feed table will create uneven cuts or jam the material on out-feed. There are a few other things to keep in mind regarding your material as well. Make sure the material you are cutting is free of all foreign objects. Do not cut materials that may have nails or screws as they will damage the blade and may cause injury to you. Also, if the material contains a loose knot it can break free and create a safety hazard. Only cut with the grain, attempting to cut across the grain of material will create poor results and could create kick-back. Do not attempt to joint end grain either. If you have a cupped board place the concave side down on the table while running it through the machine. This will help remove material on the ends and flatten out the board.  
   −
If your material looks good, the next step is to set up the jointer itself. When setting up the jointer in-feed table, make sure not to remove more than 1/16" of material. This limits the amount of cutter engagement and will help prevent a kickback. You will also need to hook up the adjacent dust collector to the end of the machine, make sure it is plugged in, and turned on. The dust collector must be used with the jointer to help keep the dust out of the air. As you make a cut, it is imperative that you keep the wood firmly against the fence and table. Therefore, you should double check to see if the fence is secure, especially because the fence can be adjusted.  You do not want the fence to move while you are making a cut.
+
It's always a good idea to examine the material for flaws and come up with a game plan prior to making your first cut.  If the material has cupped side you should start with the cupped side down. If your material looks good, the next step is to set up the jointer itself. When setting up the jointer in-feed table, make sure not to remove more than 1/16" of material. This limits the amount of cutter engagement and will help prevent a kickback. You will also need to hook up the adjacent dust collector to the end of the machine, make sure it is plugged in, and turned on. The dust collector must be used with the jointer to help keep the dust out of the air. As you make a cut, it is imperative that you keep the wood firmly against the fence and table. Therefore, you should double check to see if the fence is secure, especially because the fence can be adjusted.  You do not want the fence to move while you are making a cut.
    
After the jointer is set up you are ready to cut. Press the power switch and slowly push the material through, making sure to keep your hands away from the cutter head/guard. Do not stop pushing the material until after the cut is finished. If the material gets stuck and won't move forward continue to hold onto the work and very carefully turn off the power switch. Do not let go of your work piece during the cut or it could fly backwards.
 
After the jointer is set up you are ready to cut. Press the power switch and slowly push the material through, making sure to keep your hands away from the cutter head/guard. Do not stop pushing the material until after the cut is finished. If the material gets stuck and won't move forward continue to hold onto the work and very carefully turn off the power switch. Do not let go of your work piece during the cut or it could fly backwards.
1,948

edits

Navigation menu