Difference between revisions of "Virtual Reality Welding Station"
| Line 23: | Line 23: | ||
== Documentation == | == Documentation == | ||
| + | Setting up Simulator | ||
| + | Plug in extension cord (make sure it won’t trip anyone) | ||
| + | Flip switch on back of machine | ||
| + | Press power button on the front of the machine | ||
| + | Attach welding process of your choice (see welding processes section down below) | ||
| + | At login screen, select user | ||
| + | Select right or left handed | ||
| + | Open Exercise | ||
| + | Place Helmet on head and size to head | ||
| + | |||
| + | |||
| + | Clean up | ||
| + | Take helmet off at place on 2nd shelf of cart | ||
| + | Disconnect welding process | ||
| + | Exit out of the exercise | ||
| + | Press power button on front of the machine, and wait for screen to be completely blank | ||
| + | Flip the switch to off on the back of machine | ||
| + | Unplug the extension cord and leave it coiled up neatly underneath the cart | ||
| + | Stack work pieces neatly | ||
| + | Coil up all torches used and neatly place on the bottom shelf of the cart | ||
| + | |||
| + | Switching Welding Processes | ||
| + | MIG | ||
| + | Take connector of MIG torch and align 4 holes with machine (left side) | ||
| + | Twist the threaded end, but do not over tighten | ||
| + | Stick | ||
| + | Grab clamp with small cord attached | ||
| + | Line up the 5 holes of the connector with that of the machine (right side) | ||
| + | To remove, press silver button and softly pull straight out (do not twist) | ||
| + | TIG | ||
| + | Grab cable with TIG torch attached | ||
| + | Align 4 holes of the connector with that of the machine (left side - same as MIG) | ||
| + | Screw in while holding the connector (do not over tighten) | ||
| + | To remove, unscrew the connector | ||
| + | |||
| + | |||
| + | Warnings | ||
| + | Don’t drop the helmet, always place on cart when your not wearing it | ||
| + | When someone enters the tool room, make sure they know about the extension cord | ||
| + | Do not aggressively over tighten the connectors of the welding torches | ||
| + | Make sure to press silver button when releasing the connector of the stick torch | ||
| + | Do not cut power to the machine before it is completely shut down (clean up #4 & #5) | ||
| + | Always lay torches completely on top of the table | ||
| + | Make sure overhead clamp is secured tightly before using | ||
| + | |||
| + | |||
| + | Simulator Video: | ||
| + | https://www.millerwelds.com/equipment/training-solutions/training-equipment/augmentedarc-augmented-reality-welding-system-m30100 | ||
== Training == | == Training == | ||
Revision as of 13:57, 22 March 2019
The current Ace of the Virtual Reality Welding Station is Wyatt Bertis (wbertis22@georgefox.edu).
Documentation
Setting up Simulator Plug in extension cord (make sure it won’t trip anyone) Flip switch on back of machine Press power button on the front of the machine Attach welding process of your choice (see welding processes section down below) At login screen, select user Select right or left handed Open Exercise Place Helmet on head and size to head
Clean up
Take helmet off at place on 2nd shelf of cart
Disconnect welding process
Exit out of the exercise
Press power button on front of the machine, and wait for screen to be completely blank
Flip the switch to off on the back of machine
Unplug the extension cord and leave it coiled up neatly underneath the cart
Stack work pieces neatly
Coil up all torches used and neatly place on the bottom shelf of the cart
Switching Welding Processes MIG Take connector of MIG torch and align 4 holes with machine (left side) Twist the threaded end, but do not over tighten Stick Grab clamp with small cord attached Line up the 5 holes of the connector with that of the machine (right side) To remove, press silver button and softly pull straight out (do not twist) TIG Grab cable with TIG torch attached Align 4 holes of the connector with that of the machine (left side - same as MIG) Screw in while holding the connector (do not over tighten) To remove, unscrew the connector
Warnings
Don’t drop the helmet, always place on cart when your not wearing it
When someone enters the tool room, make sure they know about the extension cord
Do not aggressively over tighten the connectors of the welding torches
Make sure to press silver button when releasing the connector of the stick torch
Do not cut power to the machine before it is completely shut down (clean up #4 & #5)
Always lay torches completely on top of the table
Make sure overhead clamp is secured tightly before using
Simulator Video:
https://www.millerwelds.com/equipment/training-solutions/training-equipment/augmentedarc-augmented-reality-welding-system-m30100