2,292
edits
Changes
Jump to navigation
Jump to search
Line 39:
Line 39: − + Line 224:
Line 224: − + − + − + − + − + − + − + − + − + − + − + − +
→Train Whistle Body
<br>
<br>
<br>
<br>
<strong>Step 2:</strong> Select the Front Plane in the design tree (the left column on your screen) to begin your sketch. Click on the Sketch tab above and click Sketch.
<strong>Step 2:</strong> Select the Top Plane in the design tree (the left column on your screen) to begin your sketch. Click on the Sketch tab above and click Sketch.
[[File:TW2.png|1500px|none]]
[[File:TW2.png|1500px|none]]
<strong>Step 35:</strong> Cut the four holes using the [[Wood Drill Press|wood drill press]].
<strong>Step 35:</strong> Cut the four holes using the [[Wood Drill Press|wood drill press]].
TW35
[[File:TW35.jpg|500px|none]]
<br>
<br>
<br>
<br>
<strong>Step 36:</strong> Mark the areas that will be cut out on the side of the train whistle.
<strong>Step 36:</strong> Mark the areas that will be cut out on the side of the train whistle.
TW36
[[File:TW36.jpg|500px|none]]
<br>
<br>
<br>
<br>
<strong>Step 37:</strong> Cut the four triangular pieces using the [[Vertical Wood Bandsaw|wood bandsaw]].
<strong>Step 37:</strong> Cut the four triangular pieces using the [[Vertical Wood Bandsaw|wood bandsaw]].
TW37
[[File:TW37.jpg|500px|none]]
<br>
<br>
<br>
<br>
<strong>Step 38:</strong> Flatten a length of 1/2-inch wooden dowel down to 3/8 inch using the [[Disc/Belt Sander|disc/belt sander]]. Cut the flattened dowel into four pieces a bit longer than you will need for the fipple blocks using the wood bandsaw.
<strong>Step 38:</strong> Flatten a length of 1/2-inch wooden dowel down to 3/8 inch using the [[Belt/Disc Sander|belt/disc sander]]. Cut the flattened dowel into four pieces a bit longer than you will need for the fipple blocks using the wood bandsaw.
TW38
[[File:TW38.jpg|500px|none]]
<br>
<br>
<br>
<br>
<strong>Step 39:</strong> Test the fipple blocks before gluing. Take note of the placement of each fipple block that gives the best sound for each hole. You can use a bit of extra wooden dowel to hold them in place.
<strong>Step 39:</strong> Test the fipple blocks before gluing. Take note of the placement of each fipple block that gives the best sound for each hole. You can use a bit of extra wooden dowel to hold them in place.
TW39
[[File:TW39.jpg|500px|none]]
<br>
<br>
<br>
<br>
<strong>Step 40:</strong> Glue the fipple blocks in place and use a bit of extra wooden dowel to hold them in place. Let the glue sit overnight before working on the train whistle body again.
<strong>Step 40:</strong> Glue the fipple blocks in place and use a bit of extra wooden dowel to hold them in place. Let the glue sit overnight before working on the train whistle body again.
TW40
[[File:TW40.jpg|500px|none]]
<br>
<br>
<br>
<br>
<strong>Step 41:</strong> Cut a 1.5x1.5x0.75 inch block for the mouthpiece. Use a 1 3/8 Forstner bit and a 1/2 drill bit for the holes in the mouthpiece.
<strong>Step 41:</strong> Cut a 1.5x1.5x0.75 inch block for the mouthpiece. Use a 1 3/8 Forstner bit and a 1/2 drill bit for the holes in the mouthpiece.
TW41
[[File:TW41.jpg|500px|none]]
<br>
<br>
<br>
<br>
<strong>Step 42:</strong> After the glue has dried, use the wood bandsaw and the belt/disc sander to remove the extra length of the fipple blocks.
<strong>Step 42:</strong> After the glue has dried on the train whistle body, use the wood bandsaw and the belt/disc sander to remove the extra length of the fipple blocks.
TW42
[[File:TW42.jpg|500px|none]]
<br>
<br>
<br>
<br>
<strong>Step 43:</strong> Glue the mouthpiece on top of the train whistle body and let it sit overnight. Once the glue has dried, your train whistle is ready to make some noise. Feel free to sand the edges down, hand-carve or burn-in a design, stain the wood, apply lacquer/finish, and/or engrave something on it using the [Laser Cutter|laser cutters]]. Enjoy!
<strong>Step 43:</strong> Glue the mouthpiece on top of the train whistle body and let it sit overnight. Once the glue has dried, your train whistle is ready to make some noise. Feel free to sand the edges down, hand-carve or burn-in a design, stain the wood, apply lacquer/finish, and/or engrave something on it using the [[Laser Cutters|laser cutters]]. Enjoy!
TW43
[[File:TW43.jpg|500px|none]]
<br>
<br>
<br>
<br>