Wood Shop

From maker-hub
Jump to navigation Jump to search

The wood shop is a 975 square foot space. It contains a table saw, radial arm miter saw, planer, jointer, drill press, bandsaw, scroll saw, oscillating spindle sander, combination belt and disc sander, lathe, and other hand tools. It also contains a large CNC router. The shop is also equipped with compressed air quick connections for powering tools and machines. There are two air filtration units located up high in the ceiling. When producing wood dust turn on the filtration units with the white remote control. Theses do a good job of removing a large percentage of the wood dust from the air.

The Prototype Lab

The current Ace of the Wood Shop is Needed (Makerhub@georgefox.edu).

Schedule

View the most up-to-date Wood Shop schedule on this Google Sheet.


Equipment Overview

NameCompanyModelCurrent Ace 
Belt SanderRigidR2740Needed
Belt/Disc SanderPowerMaticBD31ANeeded
CNC RouterLagunaSmartShop IILuke Roderick
Compound Miter SawDewaltDWS780Needed
Hand RouterPorter Cable8902Needed
Handheld CNC RouterShaperS01-NN OriginNeeded
JointerPowermatic54HHNeeded
Oscillating Spindle SanderGrizzly IndustrialG1071Needed
PlanerPowermatic209HH-3Needed
Power CarverForedomSR - K5200 DeluxeNeeded
Router TableBora PortamatePM-P254Needed
Scroll SawExcaliburEX-21Needed
Table SawSawStopPCS31230Needed
Vertical Wood BandsawLagunamband 14BX220-250Needed
Wood Drill PressTenka ToolNova Voyager DVRNeeded
Wood LatheTeknaToolNova Galaxi DVRNeeded

3 commandments

1. Safety First

Safety First is the rule we hold highest of the three. This rule applies to both the safety of you as well as others

Keeping yourself safe in the Machine Shop is very important, as there are possibilities for accidents if you don't follow the safety guidelines. Safety starts with you so don't depend on others to keep you safe. There is a first aid kit located on the south wall near the Wood Shop door.
The following rules must be followed at all times.


. Safety glasses must be worn when crossing into the shop area marked on the floor.

·        No horseplay in the shop.

·        Don’t do anything distracting to yourself or others while operating machinery.

·        Do not wear any loose clothing, jewelry, or lanyards.

·        No hats or open toed shoes.

·        Hair will not extend below the collar.

·        Do not wear gloves while operating powered machinery.

·        Food or drink is allowed when not operating machinery as long as it is kept a safe distance away from the machines.

·        Do not attempt to operate machinery in the shop that you have not been certified on by GFU engineering personnel.

·        Do not argue with volunteers or shop staff. Contact Justin Johnson if you have issues that need to be resolved.

·        Do not operate machinery without a shop supervisor or trained volunteer in the shop with you. Never operate equipment alone in the shop.

·        Reset the space. Make the area you are working in ready for the next person using the dust broom and vacuum cleaner.

·        The first aid kit is located in the machine shop, next to the Wood Shop doors.

·        If you see a safety violation inform the person immediately and encourage them to comply with the policies

·        Don’t do anything that would require an additional rule to be added to this list.

2. Reset the Space

The Machine Shop has a specific organization to it. Put whatever you use back where it belongs. There is a place for everything and everything has a place. This rule applies to everything in the space. If you use a tool, put it back. If you use a pen, put it back. Throw away your trash and recycling.

Now, we understand that sometimes you need to leave projects out. Maybe you are in the middle of a large project and you need something left overnight. In cases like this, it is okay, but you NEED to make prior arrangements with Nick or Justin.

Please put back the Machinery the way you found it. Clean up chips and any messes you make. NEVER use shop air to clean off yourself or the machines.

Always put any unused materials back on the storage shelf, and throw away unusable scrap.

Always leave the space better than you found it.

3. Be Professional

This commandment has two sides to it. It covers the idea of acting like professional (which Webster’s defines as “exhibiting a courteous, conscientious, and generally businesslike manner in the workplace”). The term also describes the standards of education and training that prepare members of the profession with the particular knowledge and skills necessary to perform their specific role within that profession. Hopefully, you are learning both of these as part of your education at George Fox University. In the Welding Lab we expect you to develop as a courteous, conscientious, and skilled craftsman, understanding the tools and equipment in the Maker Hub and how to use them effectively.

Being a professional has some obvious ramifications in terms of behavior. First, be Christlike. Think of others better than yourselves. Share. If you have been welding for a prolonged time and someone else is waiting for the machine, let them use the machine for a while. This is being a professional.

If you are learning to how to use a machine, and you can't something to work the way you want - ASK SOMEONE! Learn! Become a professional. Learn the craft. This is an educational space. You might think it will be quick and you can just get it done “your” way and not learn how to do it correctly. Be a Professional and learn the proper way, and then be available to teach others.

One very important, and likely difficult part of being a professional is to correct others when they are not being professional. It is your responsibility to speak up when you see somebody doing something inappropriate. If you see somebody doing something unsafe, not resetting the space, or being unprofessional, the professional thing to do is to remind them of the three commandments and ask them politely to correct their action. This is OUR space, not any individual's. As a group, we expect everyone in the space to keep the space safe, clean, and operable for everyone. 

If someone acts disgracefully unprofessional to you in the Machine Shop, you are welcome to bring the issue to Justin or Nick's attention.

General Wood Shop Knowledge

Welding is the process of joining metals together. It is a form of additive manufacturing. There are several different types of welding, and the Welding Lab uses most of these including spot welding.

In the Welding Lab, metals are joined together using MIG (Metal Inert Gas), TIG (Tungsten Inert Gas), Stick and spot welding.

Each welder has its own special purpose and benefits. MIG is fast and much easier to learn than TIG welding. Spot welding is only used with sheet metal. TIG welding produces very clean welds and the heat is more confined to a smaller area. TIG will also allow you to weld very thin metals.

These are a few good steps to having a successful weld.

  • Make sure the materials have no coatings. Welding of some coatings like galvanized metal can produce toxic fumes.
  • Materials should be properly prepped and clean for best results.
  • Make sure the process you are using is correct for your material type.
  • Double check the weld settings and use a piece of scrap to practice before welding on your project.
  • Only weld steel and aluminum. Do not attempt to weld unknown materials.

Here are a couple things to keep in mind:

  • Material will be very hot after welding so always think before touching.
  • Make sure the welder is properly grounded before attempting to weld.
  • Never weld in wet clothes or around water.
  • Never try to weld any type of tank that has ever held flammable liquids. This is very dangerous and can explode!
  • Always check your welding hood settings prior to welding. (start with a darker setting and work your way down.
  • Welding takes lots of practice so don't be afraid to ask for help.


SLA Printing

Inverted SLA Process

Stereolithography, SLA, is a part of the manufacturing technology of vat polymerization. This means a light source (laser) is used to cure liquid resin into a hard plastic. The Form 2 is the only 3D printer that the Prototype Lab has that is an SLA printer. It utilizes the Upside Down or Inverted orientation. The resin tank has a clear bottom with a surface the resin will not stick to. This allows the resin to cure against the bottom of the tank. The build platform is lowered into the resin until it is hovering above the bottom surface of the tank, as far away as the height of the layer to be constructed. The laser is directed through the bottom of the tank and cures a layer of resin onto the build platform. Then, the resin tank slides over and the build platform raises. The wiper will then sweep across the tank to circulate the resin. The build platform will lower again, and the process will be repeated until the print is completed. Due to friction caused by de-laminating every layer, every part should be canted in its orientation. This means the part should be angled to reduce the cross sectional area needing to be shifted to de-laminate each layer. This de-lamination also causes the Form 2 to be the Prototype Lab's slowest 3D printer. Once a part is finished on the Form 2, it must be removed off of the build plate. Try to avoid scraping the build plate when removing parts. Any excess resin must be washed off using the Form Wash, the part must be air dried so that any isopropyl alcohol from the Wash has evaporated, the part should be cured in the Form Cure, and supports should be clipped off. Any remaining support marks can be sanded off if so desired. Extra information on SLA Printing can be found here.

FDM Printing

Fused Deposition Modeling (FDM) printers use a thermoplastic filament, which is heated to its melting point, then extruded to create layers which then build an object. There are many different types of FDM printers. Some use a modeling material and a support material, some just use a modeling material which when creating support will use a different style of layering that allows the filament to break off easily, some are able to use multiple filaments at once allowing for multicolored objects to be created.

Example of a filament spool for a FDM printer.

Both Stratasys printers (Dimension and F370) use soluble support filament (the support filament dissolves in a heated sodium hydroxide bath), the Prusa printers use only a model material, and the Markforge printer only uses model material as well (however it will layer another filament for extra support).

The filament for these printers comes in spools (basically thin plastic ropes that are wound up). The filament is fed through an extruder head, heated to the desired temperature, then extruded (similar to what happens with a hot glue gun).

FDM printers can work with various materials, in the Prototype Lab we mainly stick to ABS which is used by the Stratasys machines and PLA which is used by the Prusas. The Markforge uses a material called Onyx (nylon and plastic mix) and will layer in another filament such as Carbon Fiber, Kevlar, etc.

General Bead Blasting Knowledge

Bead blasting is the process of using compressed air to propel small glass beads for ablating and cleaning a material surface. Different types of blast media are used in industry including Soda, Walnut shells, Sand and many more material types.
These are a few good steps to having a Success with glass beading.

  • Make sure the material is free from heavy grease and dirt.
  • The material needs to physically fit into the blast cabinet.

Here are a couple things to keep in mind:

  • Never point the nozzle at the gloves or window.
  • Make sure the power switch is turned on before use.
  • Always wait 5 minutes after use before opening the cabinet door.
  • Never try to bead blast anything flammable. Blasting can sometimes create sparks.
  • Never activate the foot pedal with the cabinet door open.


Foxtale Certification

Before working with any of the equipment in the Wood Shop you will need to take the general lab quiz as well as the specific quiz for each machine you are trying to use. The enrollment code for all of the quizzes is MakerHub.



The wood shop is 975 sq. ft. and contains a table saw, radial arm miter saw, planer, jointer, drill press, bandsaw, scroll saw, oscillating spindle sander, combination belt and disc sander, lathe, and other hand tools. It also contains a large CNC router. The shop is also equipped with compressed air quick connections for powering tools and machines. There are two air filtration units located up high in the ceiling. When producing wood dust turn on the filtration units with the white remote control. Theses do a good job of removing a large percentage of the wood dust from the air.

Equipment


3 commandments