Windchimes

From maker-hub
Revision as of 13:51, 14 June 2021 by Cpainter17 (talk | contribs)
Jump to navigation Jump to search


Chimes 29.png


This TV will have you draw the chimes in SolidWorks, cut them in the Laser Cutter, and build your own set of windchimes using acrylic discs and pre-made chimes.









Procedure

Buckle up...

SolidWorks

Step 1: Open SolidWorks 2020, and select a new part. Don't forget to save your file frequently as you go. In the bottom-right corner of your Solidworks window, set the units to IPS (inch, pound, second).

Chimes 1.png



Step 2: Select the Top Plane in the design tree (the left column on your screen) to begin your sketch. Click on the Sketch tab above and click Sketch.

Chimes 2.png



Step 3: We are going to start with the main hanger. The first circle is going to be centered at the origin. Select the circle command in the sketch pane. Where you select is going to be the center of the circle, so click the origin and build out the circle at any size.

Chimes 3.png



Step 4: Using the Smart dimension tool, make the diameter of the circle 2 in

Chimes 4.png


Offset the circle inwards a distance of 0.15 in

Chimes 5.png



Step 5: Draw a construction line from the quadrant point of the inner circle to the quadrant point of the outer circle.

Chimes 6.png


Draw a small circle centered at the midpoint of the construction line. Set the diameter to 0.05 in

Chimes 7.png


We are going to make a total of four of these circles around the perimeter of the circle using a sketch pattern. These are going to be used to tie the hanging strings to. Select the small circle, then the drop down arrow next to “Linear Sketch Pattern” in the sketch pane. Select “Circular Sketch Pattern”

Chimes 8.png


In the sidebar, change the number of instances to 4 and click the green check mark. This will make 4 evenly spaced, identical circles around a center point.

Chimes 9.png
Chimes 10.png


Using the same beginning circle, create another circular array with 5 instances

Chimes 26.png



Step 6: We are going to extrude this sketch to make the hanger using contours. While still in the sketch, select the “Extruded Boss/Base” command The thickness will be the same as your material. In this TV we are using ¼” acrylic.

We want to extrude the outer circle and still have the holes cut out with a hollow center. SolidWorks may be smart and do this for you automatically, but if not, open the “Selected Contours” section in the sidebar and select the area between the two large circles. It should look the this:

Chimes 11.png


Hit the green check mark to create the 3D solid

Chimes 12.png



Step 7: Next we are going to create the center circle that will hit against the chimes. Normal to the top plane and start a new sketch with a circle centered at the origin. This one will be smaller with a diameter of 1 in

Chimes 13.png


This one needs a hole in the center. Create a small circle with a diameter of 0.05 in

Chimes 14.png



Step 8: When we extrude this circle, we want it to be lower than our holder, so we are going to use the “Offset” option. Select “Extruded Boss/Base and in the sidebar change the “from” option from Sketch Plane to Offset. This offsets the beginning of the extrusion from the sketch plane. Enter an offset distance of 2 in, and an extrusion thickness of 0.25 in.

Chimes 15.png



Step 9: We are going to make the ornamental hanging piece that goes at the bottom. This can be any shape as long as it is about 1 in wide and no more than 2 in tall. I am going to make a teardrop diamond shape for mine.

The first step is to create a sketch in the front plane. Draw a construction line from the origin and down to about 2 inches below the center circle. (This is not specific since it is just for visualization)

Chimes 16.png


Draw your hanging shape at the end of the construction line.

Chimes 17.png


Extrude the piece the same ¼”, but this time change the direction 1 to “Mid-Plane”

Chimes 18.png


After finishing that piece, you have drawn each piece that you will be laser cutting and have a general idea of how it will look when hanging.

Chimes 19.png



Step 10: Since we are going to be cutting these pieces on the laser cutter, we need to export them as .dxf so the laser cutter program can read it.

Go to “File > Save as” and change the type to .dxf We are going to have to do this twice since not all of our faces are parallel. This will prompt you to select what view or faces you want to export. Select the “Faces/loops/edges” option and select the top faces of the two circle hangers.

Chimes 20.png


This will export those faces as 2D vectors that can be put into inkscape and prepared for cutting.

Chimes 21.png


Repeat these steps and select the front face of the hanger.

Chimes 22.png
Chimes 23.png

Inkscape

Next we are going to prepare our .dxf files for the Laser Cutter using Inkscape. This is about what the file should look like. Details for preparing the file and instructions for cutting the pieces can be found on the Laser Cutter wiki page. As a note, all cut lines should be fully red (255,0,0) and all engraving should be fully black (0,0,0)

Chimes 24.png


If you want, you can engrave a design into the hanging piece. Find a design you like on google and import it into Inkscape. Prepare the image as necessary according to the wiki page. I am going to add in a simple floral design.

Chimes 25.png


Once the pieces are prepared in Inkscape, follow the instructions on the Laser Cutter wiki page to cut out the pieces.

Hanger

Use TIG rod to make a small hanger. Begin with about 3 in of the rod and go to the hand bender. With the ¼” die in the center, bend one end of the rod into a full circle. Bend the other into a “C” shape, enough so it can hook onto something without falling off.

Assembly

You should have three acrylic pieces, the ring with holes, the small circle with a center hole, and the decorative hanger. You will also have received 5 chimes of varying lengths. Using these pieces and sewing thread, you will assemble your windchimes.

First we are going to tie the hanging string. Using a single piece, thread the string through the four quadrant holes, tying the first one and the last one. It should look about like this:

Chimes 27.png



Next you are going to tie on the chimes, there are many ways to do this. You will tie the chimes in the leftover holes, and double up on the top hole (the one you based the second array off of)

In this TV I used a single thread and wove it through the holes and chimes. Then I hung it on my hook so I could even out the hanging lengths simply by pulling the string.

Chimes 28.png



There will be one more string with the hanger tied to the end and the small circle tied near the middle. String a bead to where you want the center disc to sit and tie it. This bead will prevent the disc from sliding down.

Pull the string through the center of the main holder and tie it to the hook at a height that the center disc will bang on the chimes.

Chimes 29.png