Difference between revisions of "Speedy 400"

From maker-hub
Jump to navigation Jump to search
Line 17: Line 17:
 
[[{{#show: {{FULLPAGENAME}}|?Has icon|link=none}}|100px|left|top|{{#show: {{FULLPAGENAME}}|?Has icondesc}}]]
 
[[{{#show: {{FULLPAGENAME}}|?Has icon|link=none}}|100px|left|top|{{#show: {{FULLPAGENAME}}|?Has icondesc}}]]
 
[[{{#show: {{FULLPAGENAME}}|?Has image|link=none}}|300px|thumb|upright=1.5|{{#show: {{FULLPAGENAME}}|?Has imagedesc}}]]
 
[[{{#show: {{FULLPAGENAME}}|?Has image|link=none}}|300px|thumb|upright=1.5|{{#show: {{FULLPAGENAME}}|?Has imagedesc}}]]
 +
 +
Make: {{#show: {{PAGENAME}} |?Has make}}
 +
 +
Model: {{#show: {{PAGENAME}} |?Has model}}
 +
 +
Ace: {{#show: {{PAGENAME}} |?Has ace.Has name}} ({{#show: {{PAGENAME}} |?Has ace.Has email address}}).
 +
 +
Location: {{#show: {{PAGENAME}} |?Is located in facility}}
 +
 +
==Description==
 +
 +
Insert Description Text
 +
 +
Here is an example of this piece of equipment being used.
 +
 +
Insert video media here.
 +
 +
==Documentation==
 +
 +
====Terminology====
 +
 +
Insert terminology here
 +
 +
User Manual
 +
 +
==Training==
 +
====Overview====
 +
 +
Insert Text
 +
 +
====Demonstration====
 +
 +
Insert text
 +
 +
====General Procedure====
 +
 +
Insert text
 +
 +
==Safety==
 +
Insert text
 +
 +
==Certification==
 +
 +
Foxtale Quiz
 +
 +
==Troubleshooting==
 +
 +
==Maintenance==
 +
====General maintenance====
 +
 +
Insert text
 +
 +
====Specific Maintenance Tasks====
 +
{| class="wikitable"
 +
!Maintenance Procedure
 +
!Frequency
 +
!Done By
 +
|-
 +
|Sample
 +
|Sample
 +
|Sample
 +
|}
 +
 +
 +
 +
 +
 +
 +
 +
 +
 
Description here.
 
Description here.
  

Revision as of 12:18, 6 November 2019

Laser Engraver Icon
The Trotec Speedy 400 Laser Engraver

Make: Trotec

Model: Speedy 400

Ace: Zach Cogswell (zcogswell18@GeorgeFox.edu).

Location: Prototype Lab

Description

Insert Description Text

Here is an example of this piece of equipment being used.

Insert video media here.

Documentation

Terminology

Insert terminology here

User Manual

Training

Overview

Insert Text

Demonstration

Insert text

General Procedure

Insert text

Safety

Insert text

Certification

Foxtale Quiz

Troubleshooting

Maintenance

General maintenance

Insert text

Specific Maintenance Tasks

Maintenance Procedure Frequency Done By
Sample Sample Sample





Description here.

The current Ace of the Speedy 400 is Zach Cogswell (ZCogswell18@GeorgeFox.edu) Zach Cogswell zcogswell18@GeorgeFox.edu


Documentation

Essentially the same as Speedy 300. The Speedy 400 uses the same software and general setup as the Speedy 300, however it has a larger bed and a few backend setting differences.

NOTE: Currently, the Speedy 400 should not be used for acrylic**. There are some issues with settings/airflow that cause acrylic to often catch fire while cutting (which, as you would imagine, is bad)

** If you know what you are doing and are very careful, small (<10 inches) pieces of 1/4" or 1/8" acrylic allow for sufficient airflow to avoid catching fire. Small pieces of 1/2" acrylic can often work as well, as long as you are careful. If the fumes light fire while cutting, pause the print IMMEDIATELY (the same button as start), or, if needed, stop it entirely (although this will abort the cut and you will not be able to continue). Often pausing allows the fire to go out and the acrylic to cool down, so for small cuts you may be able to continue, carefully, after pausing. If you must cut large sheets of acrylic, remove the paper from the area you are cutting, as close to the size of your cut as possible. Although it is not the paper that is burning, removing it seems to reduce the possibility of fire. Try not to remove any more paper than absolutely necessary, as the paper keeps the acrylic clean and protected from scratches when in the stock pile.

Training

See Speedy 300 Training