Difference between revisions of "Router Table"

From maker-hub
Jump to navigation Jump to search
Line 99: Line 99:
 
* Leave an eighth inch gap of exposed shank when mounting the bit in the collet.
 
* Leave an eighth inch gap of exposed shank when mounting the bit in the collet.
 
* Lock the height adjustment before turning on the router table.
 
* Lock the height adjustment before turning on the router table.
* Use the available feather boards and push sticks to keep your hands away from the spinning bit.
+
* Use the available feather boards and push blocks to keep your hands away from the spinning bit.
 
* When using the fence, always move your workpiece from right to left.
 
* When using the fence, always move your workpiece from right to left.
 
* Never position the fence so that the workpiece travels between the router bit and the fence.
 
* Never position the fence so that the workpiece travels between the router bit and the fence.

Revision as of 14:33, 2 March 2022

Router Table Icon 2.png
Router Table.jpg

Make: SawStop/Bora Portamate Motor

Model: RT-LFT 4-Post

Serial Number: 107015

Ace: Needed (gdowler@georgefox.edu).

Location: Wood Shop


Description

A router table can be used to make custom moldings and make slots in workpieces. Router tables are extremely versatile in the types of cuts they can perform. Holes and channels of varying depths and nearly limitless shapes can be cut. The router table can also use special bits to cut bevels and chamfers along the edges of a workpiece.

Introductory Video

Things you can do with a router table

Documentation

Terminology

Each bit is made for a different job. The wood shop has a wide assortment, although less common types may be unavailable. It should be noted that different bit sizes and profiles will operate better at different speeds. A good rule of thumb for setting the router bit speed is: the larger the cutter the slower the speed. Usually the router table will be set to 20000 RPM. If you plan to use a larger bit and reduce the speed of the router, ask a shop supervisor for assistance.

Router Bit Chart.jpg
RouterBits.jpg

Definitions

Table Router User Manual

Training

Operation

Router Feed Direction.jpg
Router Incorrect Feed Direction.jpg

Changing a Bit

Always unplug the router before changing a bit.

Always raise the router collet above the throat plate when changing bits. Insert the bit until the cutting edge touches the collet then pull the bit out about an eighth inch and finger tighten the collet. It’s important to allow an eighth inch of space between the bit and the collet. Router bits can heat up quickly when in use. This heat causes expansion, and the eighth inch space between the bit and the collet allows for this expansion. Router bits that are not installed properly can come loose while making your cut.

Use the two wrenches to tighten the locking nut on the collet.

Setting the Fence

When setting the fence, the router fence does not need to be exactly parallel to the bit for most cuts. This differs greatly from equipment like the table saw or bandsaw which have flat blades instead of a rounded bit. The important thing is to set the fence the proper distance away from the bit, and the bit will do the rest work.

If your bit has a bearing guide, lay a straightedge against the fence and adjust it until there’s a paper-thin space between the outer edge of the bearing and the straightedge.

Feed Direction

When using the fence, always feed the workpiece from the right side of the router table to the left. The bit spins counterclockwise. The rotation of the bit pushes against the feed direction and pushes the workpiece into the fence as the user feeds the workpiece from right to left. This is the proper way to make a controlled cut on the router table. It is dangerous to feed the workpiece from left to right because the router bit will pull the workpiece out of your hands and fling it across the room.

The feed rate is how fast the workpiece moves through the router bit. A feed rate that is too fast can cause the surface of the wood to tearout. In other words, you will get a poor cut and the surface of the wood will be rough or chipped. A feed rate that is too slow can cause the wood to burn. See the troubleshooting section for more info on burning.

Material Removal

Be mindful of how much material you are removing in a single pass. If you attempt to remove too much material, you could end up straining the router motor, putting too much sideways pressure on the router bit, or cause tearout/burning on your workpiece. If you need to remove a lot of material, break it up into multiple smaller passes. If you are unsure how much material is "too much," ask a shop supervisor for assistance. Unfortunately, there is no magic number that indicates you are removing too much material. It's based on several factors including: the cross-sectional area of the material you plan to remove, the shape of the router bit, the speed of the router bit, and the hardness of the wood. With some experience, you will get a feel for how much material you can remove in a single pass.

Demonstration

Demonstrate you can safely setup the table router with a roundover bit. Remember to always unplug the router when changing tools or making adjustments to prevent an accidental turn-on situation. Perform a roundover cut on a piece of scrap wood.

General Procedure

The material you are cutting needs to be free from nails or foreign objects.

If you are shaping end grain with a router table, use a square push block behind your workpiece to support the trailing edge and prevent tearout.

Safety

Although the router table displays the SawStop logo, it does not have the SawStop technology. If your fingers come in contact with the spinning bit, the bit will not stop and it will be a very bad day for you. Remember... SAFETY FIRST!

  • Always wear safety glasses in the wood shop and wear hearing protection as applicable.
  • Always unplug the router table when changing the bit.
  • Leave an eighth inch gap of exposed shank when mounting the bit in the collet.
  • Lock the height adjustment before turning on the router table.
  • Use the available feather boards and push blocks to keep your hands away from the spinning bit.
  • When using the fence, always move your workpiece from right to left.
  • Never position the fence so that the workpiece travels between the router bit and the fence.

Certification

Canvas Quiz

Troubleshooting

Occasionally routing can leave burn marks on the workpiece. This can happen when the workpiece is fed through the router too slowly, but it can also mean that the bit in the router has become dull. Let a shop supervisor know if a bit seems dull. Sometimes the burning is due to build up of resin and other gunk (a technical term) on the backside of the blade which insulates the bit and allows for more heat to build up. Inspect the router bit before using, and make sure it looks clean. If the bit seems both clean and sharp, the cause of burning on you workpiece is either a feed rate that is too slow or a router bit speed that is too high.

Maintenance

General maintenance

  • Make sure cutter bits are clean.
  • Remove and clean the collets as needed.
  • Make sure any adjustment screws are tight.

Specific Maintenance Tasks

Maintenance Procedure Frequency Done By
Sample Sample Sample