124
edits
Changes
Jump to navigation
Jump to search
Line 10:
Line 10: − + − + − + + − + − + + + + + + + + + + + + + + Line 39:
Line 53: + + Line 52:
Line 68: − + − + − + Line 67:
Line 83: − + − ## The pressure bar is causing too much pressure on the wood. To fix, simply raise the pressure bar lever slightly and your stock should continue on its path. When it starts moving again, gently put the pressure bar lever back down. Line 82:
Line 97: − − ==Safety== − # '''NEVER''' allow your hands/fingers to enter the infeed opening. − # '''NEVER''' turn on the Thickness Planer with stock inside the infeed opening. No good. − # '''NEVER''' bend down to look into a planer while it is running. − # '''NEVER''' attempt to repair the machine or remove any panels. − # '''NEVER''' put your finger in a knot hole while operating the Thickness Planer. − +
no edit summary
|Has imagedesc=Powermatic Planer
|Has imagedesc=Powermatic Planer
|Has description=
|Has description=
|Has certification=
|Has certification=https://georgefox.instructure.com/courses/1245
|Has make=Powermatic
|Has make=Powermatic
|Has model=209HH
|Has model=209HH-3
|Has ace=Logan Hanbey;lhanbey17@georgefox.edu
|Has serial number=1706209HH5185
|Has ace=Needed;Makerhub@georgefox.edu
}}
}}
[[{{#show: {{FULLPAGENAME}}|?Has icon|link=none}}|100px|left|top|{{#show: {{FULLPAGENAME}}|?Has icondesc}}]]
[[{{#show: {{FULLPAGENAME}}|?Has icon|link=none}}|140px|left|top|{{#show: {{FULLPAGENAME}}|?Has icondesc}}]]
[[{{#show: {{FULLPAGENAME}}|?Has image|link=none}}|300px|thumb|upright=1.5|{{#show: {{FULLPAGENAME}}|?Has imagedesc}}]]
[[{{#show: {{FULLPAGENAME}}|?Has image|link=none}}|300px|thumb|upright=1.5|{{#show: {{FULLPAGENAME}}|?Has imagedesc}}]]
Make: {{#show: {{PAGENAME}} |?Has make}}
Make: {{#show: {{PAGENAME}} |?Has make}}
Model: {{#show: {{PAGENAME}} |?Has model}}
Model: {{#show: {{PAGENAME}} |?Has model}}
Serial Number: {{#show: {{PAGENAME}} |?Has serial number}}
Ace: {{#show: {{PAGENAME}} |?Has ace.Has name}} ({{#show: {{PAGENAME}} |?Has ace.Has email address}}).
Ace: {{#show: {{PAGENAME}} |?Has ace.Has name}} ({{#show: {{PAGENAME}} |?Has ace.Has email address}}).
Location: {{#show: {{PAGENAME}} |?Is located in facility}}
Location: {{#show: {{PAGENAME}} |?Is located in facility}}
__TOC__
__TOC__
==Safety First==
[[File:Safety First HD2.png|left|150px]]
* '''NEVER''' allow your hands/fingers to enter the infeed opening.
* '''NEVER''' turn on the Thickness Planer with stock inside the infeed opening. No good.
* '''NEVER''' bend down to look into a planer while it is running.
* '''NEVER''' attempt to repair the machine or remove any panels.
* '''NEVER''' put your finger in a knot hole while operating the Thickness Planer.
==Description==
==Description==
====Terminology====
====Terminology====
[[File:...Planer.png|none|thumb|500x500px]]
[[File:...Planer.png|none|thumb|500x500px]]
[[Media:1791296 man EN.pdf|Planer User Manual]]
[http://www.powermatic.com/us/en/p/209hh-20-planer-5hp-3ph-230-460v/1791316 Vendor Website]
[http://www.powermatic.com/us/en/p/209hh-20-planer-5hp-3ph-230-460v/1791316 Vendor Website]
====General Procedure====
====General Procedure====
# Connect and turn one of the dust collectors (shown below) on so we can keep the place clean. <gallery>
# Connect one of the dust collectors (shown below) on so we can keep the place clean. <gallery>
File:Small Dust Collector Image.jpg|Small Dust Collector
File:Small Dust Collector Image.jpg|Small Dust Collector
File:Large Dust Collector Image.jpg|Large Dust Collector
File:Large Dust Collector Image.jpg|Large Dust Collector
</gallery>
</gallery>
# The planer has two feed speeds, typically, the 24 fpm is used whenever possible. For softwood, the 31 FPM setting can be used.
# Make sure the material is free of all foreign objects, loose knots, and splits
# Before turning machine on, adjust the table handwheel to adjust for the board thickness.
# Before turning on the machine, loosen the table lock nuts on the side of the machine. slide the material into the machine and slowly adjust the table height by rotating the handwheel until the material
# The key is to take off very little material on the first pass and adjust as needed.
# The key is to take off very little material on the first pass and adjust as needed.
# Remove piece and adjust wheel to trim desired amount off of work piece.
# Remove piece and adjust wheel to trim desired amount off of work piece.
# Always plane with the grain, never perpendicular to grain (i.e., feed boards lengthwise, not width-wise).
# Always plane with the grain, never perpendicular to grain (i.e., feed boards lengthwise, not width-wise).
# Never attempt to force feed the planer; always allow stock to move through under the force of the feed roller only.
# Never attempt to force feed the planer; always allow stock to move through under the force of the feed roller only.
# Stock will sometimes “hang” (or stop moving forward). Causes and solutions are:
# Stock will sometimes “hang” (or stop moving forward). If the material stops feeding power off the machine and wait for the cutter to stop spinning before attempting to remove the board.
## The feed control may have slipped. Simply push it all the way to the right.
## The feed control may have slipped. Simply push it all the way to the right.
## The table is too high (not adjusted to the proper height). This should NOT happen since you’re supposed to measure the stock and then make table adjustment according to your needs.
## The table is too high (not adjusted to the proper height). This should NOT happen since you’re supposed to measure the stock and then make table adjustment according to your needs.
# Clean off the infeed table so that the next users’ stock will be able to make contact directly with the table instead of being raised up slightly by the chips left after you’re finished planing.
# Clean off the infeed table so that the next users’ stock will be able to make contact directly with the table instead of being raised up slightly by the chips left after you’re finished planing.
# Turn off and disconnect the dust collector.
# Turn off and disconnect the dust collector.
==Certification==
==Certification==
[https://foxtale.georgefox.edu/moodle/course/view.php?id=31286 Foxtale Course]
[https://georgefox.instructure.com/courses/1245 Canvas Quiz]
==Troubleshooting==
==Troubleshooting==