Difference between revisions of "Oscillating Spindle Sander"

From maker-hub
Jump to navigation Jump to search
Line 49: Line 49:
 
====Operation====
 
====Operation====
  
The spindle sander is normally used for sanding inside corners. There are various spindles of va The machine has an on/off power switch located on the control panel. Any conductive material that makes contact with the blade causes the aluminum cartridge block to fire into the blade. The blade then stops spinning and drops down out of the way. All this happens within 5 milliseconds, helping to ensure the blade inflicts minimal damage. This galvanic response safety mechanism is great for preventing injuries but will permanently damage the blade if triggered. If the material you are cutting is conductive it will trigger the saw stop feature. Do not cut any wet lumber, pressure treated, or metal coated materials such as gold leaf with this machine. Charcoal is also conductive so any laser cut areas of lumber should not make contact with the blade while cutting.  There are a few other things to keep in mind regarding your material as well. Make sure the material you are cutting is free of all foreign objects. Do not cut materials that may have nails or screws as they will damage the blade and may cause injury to you. Also, if the material contains a loose knot it can break free and create a safety hazard.  
+
The spindle sander is normally used for sanding inside corners. There are various spindles that range from 1/4" to 4". If you need to change out the spindle ask the supervisor on shift for assistance. The spindle also oscillates up and down as it rotates to produce a smooth finish. The machine has an on/off power switch located on the control panel. Make sure the material you are cutting is free of all foreign objects. Do not sand materials that may have nails or screws as they will damage the drum and may cause injury to you. Also, if the material contains a loose knot it can break free and create a safety hazard.
  
If your material looks good, the next step is to set up the saw itself. When setting up the saw the blade, it should protrude no more than 1/4" above the material top. This limits the amount of blade that is exposed and makes for a good cut. You will also want to hook up the adjacent dust collector to the rear of the machine, make sure it is plugged in, and turned on. The dust collector must be used with the table saw to help keep the dust out of the air. As you make a cut, it is imperative that you keep the wood firmly against the fence to make the cut square. Therefore, you should double check to see if you are reading the right measurement on the fence, especially because the fence can be moved to either side of the blade which is why there are two distance indicators, only one of which is correct for each set up. Make sure to ask the supervisor about the available jigs because they can be helpful for specialty cuts. Once the supervisor has demonstrated the use of a jig feel free to use it in the future but do not play around with jigs you are unfamiliar with.
+
If your material looks good, the next step is to make sure you have the appropriate spindle installed. You will also want to hook up the adjacent dust collector to the rear of the machine, make sure it is plugged in, and turned on. The dust collector must be used with the sander to help keep the dust out of the air. As you sand, it is imperative that you keep the material firmly against the table to make the surface perpendicular to the table. Hold firmly onto the material as it could get pulled out of your hands. If you are sanding the inside of a circle and the material pulls out of your hands do not attempt to grab the spinning part. If you can safely reach the power switch shut off the machine and wait for the part to stop moving.  
  
After the saw is set up you are ready to cut. Turn on the saw and slowly push the material through, making sure to keep your hands away from the blade. Do not stop pushing the material until after the cut is finished unless there is an emergency, in which case, carefully use one hand or your hip to bump the off switch. Also not let go of your work piece during the cut or it will be forced back towards you.
+
After the sander is set up you are ready to work. Turn on the sander and gently push the material into the drum, making sure to keep your hands a safe distance from the spindle. Do not force material into the drum.
  
 
====Demonstration====
 
====Demonstration====

Revision as of 16:29, 7 November 2019

Spindle Sander.png
Oscillating Spindle Sander

Make: Grizzly Industrial

Model: G1071

Ace: Needed (gdowler@georgefox.edu).

Location: Wood Shop

Description

The Grizzly vertical spindle sander is for sanding curved surfaces. The machine contains a 1HP motor and has 10 different sanding spindles ranging from 1/4" to 4" in diameter. The cast iron table has an opening that allows the spindles to oscillate up and down. The oscillating action will give you a smooth sanded surface. The 4" dust port connects easily to any dust collector. Used to remove material from wood, as well as squaring to create straight pieces.


Here is an example of this piece of equipment being used.

Documentation

Terminology

Insert terminology here

User Manual [G1071_m.pdf] User Manual

Training

Operation

The spindle sander is normally used for sanding inside corners. There are various spindles that range from 1/4" to 4". If you need to change out the spindle ask the supervisor on shift for assistance. The spindle also oscillates up and down as it rotates to produce a smooth finish. The machine has an on/off power switch located on the control panel. Make sure the material you are cutting is free of all foreign objects. Do not sand materials that may have nails or screws as they will damage the drum and may cause injury to you. Also, if the material contains a loose knot it can break free and create a safety hazard.

If your material looks good, the next step is to make sure you have the appropriate spindle installed. You will also want to hook up the adjacent dust collector to the rear of the machine, make sure it is plugged in, and turned on. The dust collector must be used with the sander to help keep the dust out of the air. As you sand, it is imperative that you keep the material firmly against the table to make the surface perpendicular to the table. Hold firmly onto the material as it could get pulled out of your hands. If you are sanding the inside of a circle and the material pulls out of your hands do not attempt to grab the spinning part. If you can safely reach the power switch shut off the machine and wait for the part to stop moving.

After the sander is set up you are ready to work. Turn on the sander and gently push the material into the drum, making sure to keep your hands a safe distance from the spindle. Do not force material into the drum.

Demonstration

Insert text

General Procedure

Insert text

Safety

There are several hazards you need to be aware of when using a spindle sander.

  • Never make contact with the rotating spindle. The sand paper is very aggressive and could cause serious injury.
  • The spindle is rotating at a high rate of speed and can grab your work piece.
  • Hold onto material firmly and keep it against the table. This will help prevent the material from getting pulled out of your hands. If material catches on the spindle it can starts rotating quickly and create a dangerous situation.

Certification

Foxtale Course

Troubleshooting

Maintenance

General maintenance

As sanding sleeves are used they will "gum up" with saw dust. If not removed, the saw dust will harden and reduce the life of the sanding sleeve. As needed, a abrasive cleaner should be used on the sleeves.

Specific Maintenance Tasks

Maintenance Procedure Frequency Done By
Sample Sample Sample