Difference between revisions of "Heat Press"
(Added Easyweed instructions) |
|||
| Line 18: | Line 18: | ||
[[{{#show: {{FULLPAGENAME}}|?Has image|link=none}}|300px|thumb|upright=1.5|{{#show: {{FULLPAGENAME}}|?Has imagedesc}}]] | [[{{#show: {{FULLPAGENAME}}|?Has image|link=none}}|300px|thumb|upright=1.5|{{#show: {{FULLPAGENAME}}|?Has imagedesc}}]] | ||
| − | + | Model: Stahls MAXX Clam Heat Press | |
| + | |||
| + | Serial Number: | ||
| + | |||
| + | Ace: '''{{#show: {{PAGENAME}} |?Has ace.Has name}}''' ({{#show: {{PAGENAME}} |?Has ace.Has email address}}). | ||
| + | |||
| + | == Description == | ||
__TOC__ | __TOC__ | ||
| Line 26: | Line 32: | ||
[https://assets.stahls.com/stahls/content/pdf/HeatPressManuals/Hotronix-MAXX-Digital-Clam-Press-Operators-Manual.pdf Operator's Manual] | [https://assets.stahls.com/stahls/content/pdf/HeatPressManuals/Hotronix-MAXX-Digital-Clam-Press-Operators-Manual.pdf Operator's Manual] | ||
| − | |||
| − | |||
== Training == | == Training == | ||
The heat press can press heat transfer applications into many materials. Be sure to check the instructions for your type of heat transfer material before pressing. | The heat press can press heat transfer applications into many materials. Be sure to check the instructions for your type of heat transfer material before pressing. | ||
| + | |||
| + | == Certification == | ||
| + | |||
| + | == Troubleshooting == | ||
| + | |||
| + | == Maintenance == | ||
| + | Due to its simplicity and limited number of moving parts this machine requires a minimal amount of maintenance. The little maintenance required consists of wiping down the machine after each use to ensure there is no dust or vinyl transferring left on the machine. To do this, grab a paper towel from either the prototype lab or the sink next to the tool room and wipe over the machine. Pay special attention to the upper platen as it is the surface that transfers heat to the vinyl. For more information on when this should be done and who should do it see the table below. | ||
| + | {| class="wikitable" | ||
| + | !Maintenance Procedure | ||
| + | !Frequency | ||
| + | !Done By | ||
| + | |- | ||
| + | |Machine wipe down | ||
| + | |After each use | ||
| + | |The student | ||
| + | |} | ||
Revision as of 09:42, 30 May 2019
Model: Stahls MAXX Clam Heat Press
Serial Number:
Ace: Needed (Makerhub@georgefox.edu).
Description
Documentation
This manual covers the use, calibration, and safety of the heat press.
Training
The heat press can press heat transfer applications into many materials. Be sure to check the instructions for your type of heat transfer material before pressing.
Certification
Troubleshooting
Maintenance
Due to its simplicity and limited number of moving parts this machine requires a minimal amount of maintenance. The little maintenance required consists of wiping down the machine after each use to ensure there is no dust or vinyl transferring left on the machine. To do this, grab a paper towel from either the prototype lab or the sink next to the tool room and wipe over the machine. Pay special attention to the upper platen as it is the surface that transfers heat to the vinyl. For more information on when this should be done and who should do it see the table below.
| Maintenance Procedure | Frequency | Done By |
|---|---|---|
| Machine wipe down | After each use | The student |