Difference between revisions of "Belt Sander"

From maker-hub
Jump to navigation Jump to search
Line 52: Line 52:
 
====Demonstration====
 
====Demonstration====
  
Demonstrate you can safely use the belt sander. You will then proceed to sand a piece of scrap material. Remember to always set the sander on its side to prevent it accidentally moving.  set the blade height so it is protruding less than 1/8" out the top of material for less exposure. When performing a rip cut the fence is used to guide the lumber into the blade. You want to make sure that the distance between the fence and blade is the width of desired cut. Mark the edge of the material when doing a cross cut so you can align the material with the blade in the sled. You can also use a miter gauge for making cross cuts but make sure the material is long enough and well supported.
+
Demonstrate you can safely use the belt sander. You will then proceed to sand a piece of scrap material. Remember to always set the sander on its side to prevent it accidentally moving or doing damageMake sure the belt is the correct grit and in good condition before use. Sand along the grain with smooth strokes. Let the weight of the sander do the work and don't push down into the work. Don't let the sander hang very far over the edge of the work piece otherwise you risk taking more material off on the edge. Always start and stop the sander off of the work piece.
  
 
====General Procedure====
 
====General Procedure====

Revision as of 13:07, 26 March 2020

Belt Sander 2.png
Ridgid R2740

Make: Rigid

Model: R2740

Ace: Needed ().

Location: Wood Shop

Description

The belt sander is good for sanding large, flat work-pieces. This is a tool that can greatly reduce the amount of time it takes to finish a project, but it can be difficult to master. Depending on the speed at which it is ran and the coarseness of the sanding belt used, this tool can remove material very quickly. This tool is best used for rough passes, and is not recommended for finely detailed or delicate work.

Here is an example of this piece of equipment being used.

Documentation

Terminology

User Manual

Training

Overview

In order to use the belt sander, begin by inspecting the sanding belt condition with the sander unplugged. Make sure the the sanding belt is not clogged with sawdust, remelted glue, or other gunk. A lever on the side will lock or unlock the belt in place. The knob located on the side near the roller allows the tracking of the sanding belt to be fine tuned. If the belt pulls to one side the knob should be used to finely adjust the roller angle to keep the sanding belt tracking. Material removal can happen quickly when using a belt sander with course grit so exercise caution. As a final step in the preparation to sand, ensure that the belt sander is set to run at an optimal speed for the type of wood and type of work to be done on that wood. The speed can be adjusted using the dial located near the hand grip.

Sand the work piece by working along the grain, and aim to overlap each pass with the the belt sander by about half of the previous passes width (1 1/2 in). The belt sander's own weight will keep it on the work piece and removing material- it should not take much additional pressure at all to sand the workpiece. Keep the belt sander flat. Rocking back and forth of the belt sander will result in scratches, nicks, and valleys in the surface. Exercise special care when the belt hangs off the work piece, not holding the belt sander flat will result in more material being taken off the edge of the piece than elsewhere. Despite the most careful handling, natural variations in wood can cause some of the wood to be sanded off faster than wood elsewhere. It is often advisable to draw lines of over the area that is to be sanded with a soft leaded pencil. By observing the gradual fading and disappearance of these lines, a flatter surface can be maintained.

When finished with the belt sander, make sure it has stopped spinning before setting it down. Never place it on the work piece as you may scratch or mar the material.

Demonstration

Demonstrate you can safely use the belt sander. You will then proceed to sand a piece of scrap material. Remember to always set the sander on its side to prevent it accidentally moving or doing damage. Make sure the belt is the correct grit and in good condition before use. Sand along the grain with smooth strokes. Let the weight of the sander do the work and don't push down into the work. Don't let the sander hang very far over the edge of the work piece otherwise you risk taking more material off on the edge. Always start and stop the sander off of the work piece.

General Procedure

Insert text

Safety

1. Both hands need to be on the sander while sanding.
2. keep hair away from the sander.
3. Always lay the sander on its side when sanding is complete.
4. Make sure to always unplug the sander before changing belts.
5. Keep the belt away from you and others.

Certification

Foxtale Course

Troubleshooting

Ask a shop supervisor for help if you have any issues.

Maintenance

General maintenance

Basic cleaning and emptying of the dust collection bag is required.

Specific Maintenance Tasks

Maintenance Procedure Frequency Done By
Sample Sample Sample